9
P/N 1010926 Rev. B 04/12
Sonic
Vertical contact toaster
A.J. Antunes & Co.
maintenance
Daily cleaning
nOte: Pre-buttering/pre-oiling the buns before
feeding them into the toaster will lead to butter/
oil accumulation on the black and silver release
sheet. this accumulation is normal. However,
excessive buildup throughout the day can lead to
buns sticking and burning. it is recommended that
the release sheet be replaced with a clean/new
release sheet once for every 6 hours of toaster
operation. the dirty release sheet can be soaked
in hot soapy water for later cleaning. continue to
rotate release sheets, alternating between the
black and silver sides, to maximize usage.
tools Required:
• heat-Resistant gloves
• Clean Towels
• Multipurpose Detergent Solution
• Sanitizer Solution
1. turn the power off, unplug the power cord, and
allow the unit to cool for 30 minutes.
2. Put on heat-resistant gloves and remove the
Butter Wheel, Pan, Heat Shield, and Bun chute
(figure 1).
3. Wash the Butter Wheel, Pan, Heat Shield, and
Bun chute in soapy water, rinse, and then wipe
them with a damp sanitized towel. allow them to
air dry.
4. Remove the Release Sheet and place it on a
clean, flat dry surface.
5. Wipe the silver side with a
clean
towel dampened
with
multipurpose Detergent solution
immedi-
ately followed by a second clean towel dampened
with sanitizer. allow it to air dry before continuing.
6. once the silver side of the Release Sheet is
dry, Repeat Step 5 on the black side. if properly
cleaned, the Release Sheet surface should be
smooth to the touch when dry.
caUtiOn
turn the power off, unplug the power cord, and allow
the unit to cool down for 30 minutes before
performing any service or maintenance.
caUtiOn
to prevent damage to the unit, do Not use abrasive
cleaners on the Release Sheet. failure to use prop-
erly cleaned Release Sheets may result in damage to
the unit and loss of warranty coverage.
7. open the front conveyor cover and firmly wipe
the conveyor Belt chain (figure 1) from left to
right and top to bottom with a clean towel damp-
ened with
multipurpose Detergent solution
immediately followed by a second clean towel
dampened with sanitizer solution.
8. close the front conveyor cover, open the rear
conveyor cover, and clean the conveyor Belt
chain as described in Step 7.
9. close the rear conveyor cover and reinstall the
Heat Shield. then plug in the power cord, turn
the unit on, count 15 seconds, then turn the unit
off and unplug the unit.
this will allow the
uncleaned sections to be exposed
.
10. open the rear conveyor cover again, clean the
newly exposed section of the conveyor Belt
chain in the same manner as before. close the
conveyor cover.
11. open the front conveyor cover again and clean
the newly exposed section of the conveyor Belt
chain in the same manner as before.
12. close the front conveyor cover and wipe down
the outside of the toaster with a clean, damp,
sanitized towel.
13. install a new or a clean Release Sheet, using the
reverse side, by draping it over both sides of the
Platen with the crease centered on the Platen.
nOte: rotate from the black side to the silver side
daily to prolong the life of the release sheet.
14. install the Bun chute so the hooks are installed
over the lower rear yellow Support Rod.
15. install the Heat Shield with the Release Sheet
retainer clips securely over the Release Sheet
and Platen.
16. Reinstall the Pan and Butter Wheel and plug in
the unit.
nOte: make sure the Heat shield is activating the
conveyor safety interlock switch. the conveyors
will not rotate unless the Heat shield is in place
and the switch is activated.
nOte: additional release sheets can be purchased
through your authorized service agency under P/n
7000249 (3-Pack) or P/n 7000250 (10-Pack).
