Sonic Electronix C1-690 Скачать руководство пользователя страница 3

3

Due to ongoing product development, all specifications are subject to change without notice.

C1-690 SPECIFICATIONS:

Continuous Power Handling:

 60 Watts

Recommended Amp Power:

 10-100 Watts per channel (RMS)

Efficiency:

 91.5 dB @ 1W / 1m  |  97.5 dB @ 1W / 0.5m

Sensitivity:

 94.0 dB @ 2.83V / 1m

Nominal Impedance:

 4 ohm

Frequency Response:

 39Hz - 22 KHz ± 3 dB

Woofer:

  

Injection-molded, mineral-filled, polypropylene cone
Rubber, positive roll surround
1.2 in. (30 mm) diameter voice coil
Flat, Conex® spider with integrated lead wires
Ferrite Magnet

Tweeter:

 

Edge-driven, silk-suspended aluminum dome
1.0 in. (25 mm) diameter diaphragm / voice coil
Ferrofluid cooling / damping
Neodymium magnet

Crossover:

 

Natural roll-off, low-pass
2nd order, high-pass filter with inductor and  
electrolytic capacitor

Included Components and Parts:

• Two (2) C1-690cw 6 x 9-inch (150 x 230 mm) woofers
• Two (2) C1-100ct 1.0-inch (25 mm) tweeters
•  Two (2) surface-mount tweeter fixtures
•  Two (2) C1-100cthp in-line, high-pass filters on  

4 ft. (1.2 m) wire harnesses

•  Two (2) metal spring clips (for tweeter flush-mounting)
• Eight (8) #8 x 1.50-inch (38mm) sheet metal screws
• Four (4) #6 x .625-inch (22 mm) sheet metal screws
• Eight (8) mounting clips
• Two (2) 4.7 mm female crimpable connectors
• Two (2) 2.8 mm female crimpable connectors
•  Two (2) 10mm stud bolts with fixed M4 nut
•  Two (2) 25mm stud bolts with fixed M4 nut
•  Two (2) M5 nuts
•  Two (2) bottom-mount spacer adaptor rings

GETTING STARTED 

•    Turn off the audio system. It is also 

advisable to disconnect the negative (–) 
terminal of your vehicle’s battery whenever 
performing installation work.

•   Before cutting, drilling or inserting any screw, 

check clearances on both sides of the planned 
mounting surface. Also check for any potential 
obstacles, such as window tracks and motors, 
wiring harnesses, etc. Check both sides of the 
vehicle, many vehicles are not symmetrical!

•   Always wear protective eyewear.

SPEAKER PLACEMENT CONSIDERATIONS

Grilles are not included with C1 speakers, as they 

are designed for installation into OEM (factory) 
speaker locations, located behind factory grilles. 
Should you need grilles, you will need to purchase 
aftermarket grilles separately.  

WA R N I N G

!!

Prolonged exposure to sound pressure levels in 

excess of 100dB can cause permanent hearing 

loss. These high-performance loudspeakers can 

exceed this level. Please exercise restraint in their 

operation in order to preserve your ability to enjoy 

their fidelity.

Содержание C1-690













Отзывы: