ASSEMBLY OF THE DEVICE
1.
Attach the rear part of grid (6) onto the motor.
2. Afterwards screw on the grid fastening nut (5).
3. Place the fan blade (4) on the spindle, then fasten it with blade fastening screw (3).
4. Hang the front part (2) of the grid on the rear part of it, so that the holes down are symmetrical.
5. Screw down together the grids, then by folding the handles fix the two grids together.
6. Place the assembled fan on the stand, and fasten it with the screw (10).
FEATURES
nominal blade diameter: 40 cm • adjustable output (3 levels) • fix status or oscillation (85°) • adjustable height (100-130 cm) • controllable dip angle
of head • dense grid • white
Figure 1.
1.
grid-fixing handles and screws •
2.
front part of grid
•
3.
blade fastening screw
•
4.
fan blade
•
5.
grid fastening nut
•
6.
rear part of grid
•
7.
motor
•
8.
speed level switches
•
9.
switch of oscillation
•
10.
fixing screw
•
11.
upper part of stand
•
12.
height fixing screw
•
13.
lower part of stand
•
14.
cover
piece
•
15.
two-part base •
16.
base fastening screws
OPERATING FAN
Ventilator can be switched on with 1, 2 or 3 speed level switches (8) and the desired speed level can be set as well. Oscillation can be turned on by
pushing (9) oscillation switch down, and can be turned off by pulling it up. You can switch off the fan with 0 button.
Dip angle of fan head part can be adjusted from the horizontal po/- 15° up or down.
CLEANING
In order to ensure optimum functioning, the unit may require cleaning at least once a month, depending on the manner of use and degree of
contamination.
1. Prior to cleaning switch off and power off the unit by unplugging it from the electric outlet!
2. Attention! Remove the front part of grid when the fan is not under power!
3. Use a slightly moistened cloth to clean the unit's exterior. Do not use any aggressive cleaners. Avoid getting water inside of and on the electric
components of the appliance!
4. Attention! Put back and fasten the protective grid to the fan, when it is not under power!
5. Only reinstall the fan afterwards!
TROUBLESHOOTING
TECHNICAL SPECIFICATION
power supply:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
30 V ~ / 50 Hz /
50
W
protection class: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . II.
3
maximum fan - air mass volume
. . . . . . . . . . . . . . . . .
F = 5
3
,
45
m /min
fan input power: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P = 4
1
,
95
W
3
service value: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SV = 1,
27
(m /min)/W
power consumption during standby position: . . . . . . . P
= 0,0 W
SB
fan acoustic power level:. . . . . . . . . . . . . . . . . . . . . . .
L = 6
3,4
dB(A)
WA
maximum air speed: . . . . . . . . . . . . . . . . . . . . . . . . . .
c = 2,
374
m/sec
service value standard: . . . . . . . . . . . . . . . . . . . . . . . IEC 60879:1986 (corr. 1992)
length of power cable:. . . . . . . . . . . . . . . . . . . . . . . . . 1,5 m
nominal blade diameter: . . . . . . . . . . . . . . . . . . . . . . 40 cm
ventilator height (adjustable): . . . . . . . . . . . . . . . . . . . 1
0
0 – 130 cm
ventilator weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2,
5
kg
Malfunction
Possible solution
The fan
does not
turn on.
Check the power supply.
Check the switches.
The fan does not oscillate.
Check the switch of oscillation.
