Caution: Risk of electric shock!
Do not attempt to disassemble of modify the unit or its
accessories. In case any part is damaged, immediately power off the unit and seek the
assistance of a specialist
.
In the event that the power cable should become damaged, it should only be replaced by the
manufacturer, its service facility or similarly qualified personnel.
Meaning of symbol on appliance:
Do not cover!
Covering the unit can cause overheating, fire or electric shock!
FEATURES
fan heater for heating the atmosphere of indoor premises • 750 / 1500 W output • operating modes: cold, warm and hot air • built-in thermostat • switchable oscillation • overheating protection • tip-
over protection • flush carrying handle • operation indicator light
ASSEMBLY (figure 1.)
1.
cold air inlet
2.
heated air outlets
3.
mode selector
4.
thermostat
5.
indicator light
6.
oscillation switch
7.
tip-over protection switch
SETUP
1.
Before switching on for the first time, carefully remove the packaging material taking care not to damage the appliance and power cable. Do not use the product if it is damaged in any way.
2.
The unit may only be used indoors in dry conditions.
3.
Set the appliance on a stable and horizontal surface. The free flow of warm air must be ensured for proper operation, therefore, please note the minimum installation distances indicated in
Figure 2.
4.
Verify that the unit’s mode selector (3) is in the OFF “0” position.
5.
Plug the unit’s standard grounded AC power cable into a grounded wall outlet. This completes the setup of the appliance.
OPERATION
The appliance’s mode selector (3) can be used to select from among the following operating modes:
0
–
Fan and heating elements off
–
„Cold air” with only the fan operating
I
–
„
Warm air” with the fan and one heating element operating
II
–
„
Hot air” with the fan and both heating elements operating
When using the
„
Cold air”
( )
function, the thermostat (4) should be set to its maximum setting.
The
thermostat
(4) can be used to set the ambient temperature of the room. In modes I and II, the appliance will switch on when the ambient air temperature falls below the value set. As the set
temperature is reached, the fan and heating elements turn off. If you would like to set a higher temperature, turn the thermostat clockwise, if you want to set it lower, then turn it counterclockwise.
The
operation indicator light
will illuminate if the appliance
( )
is operating in mode I or II. If the thermostat switches the appliance off, the indicator light will turn off.
If you notice that the operation indicator light is on in mode I or II and the fan is on but the appliance is not heating, the
overheating protection
has probably activated. Set the thermostat to its
maximum setting, and if the heating fails to activate, the safety cutoff has been activated. Set the mode selector to the
„
0” position then power off the unit by unplugging it from the electric outlet.
Allow the appliance to cool (for at least 30 minutes). Check whether the air inlets and outlets are obstructed or not, and clean them if necessary. Switch on the unit again. If the overheating
protection activates again, power off the unit by unplugging it from the electric outlet and contact the service facility.
A switch on the bottom of the appliance turns it off if it should topple over. In such cases remove power from the appliance by pulling out the power plug then stand the appliance upright and reinstall
it only afterwards according to the section entitled SETUP.
The
oscillation
(6) can be switched on or off irrespective of whether the appliance
( )
is in mode I or II. After being switched, the appliance will move and heat the air in a wider angle by oscillating
within a 90° angle. The oscillation must be switched off separately.
CLEANING & MAINTENANCE
In order to ensure optimum functioning, the unit may require cleaning at least once a month, depending on the manner of use and degree of contamination.
1.
Switch off and power off the unit by unplugging it from the electric outlet prior to cleaning.
2.
Allow the appliance to cool (for at least 30 minutes).
3.
Use a vacuum cleaner to clean the air inlet (1) and outlet (2) openings.
4
.
Use a slightly moistened cloth to clean the unit’s exterior. Do not use any aggressive cleaners. Avoid getting water inside of and on the electric components of the appliance.
TROUBLESHOOTING
DISPOSAL
This symbol of the crossed out wheeled bin – on the product or its packaging – indicates that the product should not be placed in municipal waste.
The appliance should be taken to a waste collection site licensed to collect waste electronic and electric equipment (WEEE) or the local waste management facility.
By doing so, you will protect the environment as well as the health of others and yourself.
For more information about recycling this equipment, please contact your local government, household waste disposal service or shop where you purchased
the equipment.
SPECIFICATIONS
p
ower supply:
. . . . . . . . . . . . .
230
V / 50 Hz
r
ated power:
. . . . . . . . . . . . . . 750
/
1500
W
max. power: . . . . . . . . . . . . . . 1500 W
IP protection:
. . . . . . . . . . . . .
IP20: Not protected from ingress of water.
s
ize of heater:
. . . . . . . . . . . .
2
0
x
29
x
1
6
cm
w
eight:
. . . . . . . . . . . . . . . . . . 1,6
kg
l
ength of power cable:
. . . . . .
1,
3
m
s
50
ound pressure: . . . . . . . . . . .
dB(A)
Solution
Check the section on overheating protection.
Check the fan operating mode.
Check the position
of the mode selector switch
.
Check the power supply
.
Check the section on the thermostat
.
Check the tip-over protection switch.
Set the thermostat to its maximum position
.
Clean the appliance
.
Cause
The appliance does not heat but the indicator light is on.
The appliance does not heat and the indicator light is off.
The appliance does not blow cold air ( )
The overheating protection activates frequently.
