21
EN
Copyright © 2014 Somfy SAS. All rights reserved.
Images not contractually binding
CONTENTS
1.
Prerequisite information
21
1.1 Field of application
21
1.2 Liability
22
1.3 Content
22
2.
Installation
22
2.1. Assembly
22
2.2. Wiring
24
2.3. Commissioning
24
2.4. Tips and recommendations
for installation
26
3.
Use and maintenance
28
3.1. Up and Down buttons
28
3.2. STOP function
28
3.3. Favourite position (my)
28
3.4. Operating with a Somfy
io-homecontrol sun sensor
28
3.5. Additional settings
28
3.6. Tips and recommendations for use 29
4.
Technical data
29
ORIGINAL INSTRUCTIONS
1. PREREQUISITE INFORMATION
1.1 FIELD OF APPLICATION
The Oximo 40 Auto drive is designed to motorise all types of roller blinds equipped with stops and
ULJLGOLQNVZKLFKIXO¿ODWOHDVWRQHRIWKHIROORZLQJFRQGLWLRQV
- The motorised product is controlled by a switch without a locking device (see the attached Safety
instructions document).
- When deployed, all parts of the motorised product are more than 2.50 m above ground or any other
permanent access level.
7KHDSURQRIWKHUROOHUEOLQGFDQEHUDLVHGE\FPLIDIRUFHRI1LVDSSOLHGXSZDUGVRQWKH¿QDO
slat placed 16 cm from its fully-deployed position.
If the roller shutter has slats which can open, the openings must not allow a pin of diameter 5 mm
to pass through.
These instructions apply to all versions of the OXIMO 40 AUTO io (torque/speed).
7KH2;,02$872LRGULYHGRHVQRWUHTXLUHDGMXVWPHQWDVLPSOHFRQQHFWLRQLVDOOWKDWLVUHTXLUHG
The OXIMO 40 AUTO io drive automatically programs its end limits.
The OXIMO 40 AUTO io drive can be mounted either on the right or on the left.
,WLV¿WWHGZLWK
-
obstacle protection to protect the roller shutter when it is being lowered.
-
anti-freeze protection to protect the roller shutter when it is being raised.
22
EN
Copyright © 2014 Somfy SAS. All rights reserved.
Images not contractually binding
1.2 LIABILITY
Please read these instructions carefully before installing and using the OXIMO 40 AUTO drive. In
addition to following the instructions given in this guide, the instructions detailed in the attached
Safety instructions document must also be observed.
The OXIMO 40 AUTO io drive must be installed by a motorisation and home automation
professional, according to instructions from Somfy and the regulations applicable in the
country in which it is commissioned.
,WLVSURKLELWHGWRXVHWKH2;,02$872LRGULYHRXWVLGHWKH¿HOGRIDSSOLFDWLRQGHVFULEHGDERYH
Such use, and any failure to comply with the instructions given in this guide and in the attached
Safety instructions document, absolves Somfy of any liability and invalidates the warranty.
Installers must inform their customers of the operating and maintenance conditions for the OXIMO
40 AUTO io drive and must provide them with the instructions for use and maintenance, and the
attached Safety instructions document, after installing the OXIMO 40 AUTO io drive. Any After-Sales
Service operation on the OXIMO 40 AUTO io drive must be performed by a motorisation and home
automation professional.
If in doubt when installing the OXIMO 40 AUTO io drive, or to obtain additional information, contact
a Somfy adviser or go to the website www.somfy.com.
1.3. CONTENTS
The OXIMO 40 AUTO io drive comprises two inseparable
FRPSRQHQWV
-
the drive part (A)
-
the electronic part (B)
2. INSTALLATION
Instructions which
must
be followed by the motorisation and home automation professional
installing the OXIMO 40 AUTO drive.
Never drop, knock, drill or submerge the drive.
Install a separate control point for each drive.
2.1. ASSEMBLY
It is essential to follow the order of assembly given in the instructions
2.1.1. Preparing the drive part
The drive part must always be installed before the electronic part.
Check that the inner diameter of the tube is 37 mm or greater.
1)
Fit the accessories required to integrate the drive in the
UROOHUWXEH
(LWKHU¿WWKHGULYHZKHHO$RQWKHGULYH
2U¿WWKHFURZQ%DQGWKHGULYHZKHHO&RQWKHGULYH
2)
Measure the length (L1) between the inner edge of the drive
head and the rim of the drive wheel.
Safety warning!
Caution!
Information
ȁ
Up
V
Down
1
1
1)
L1
L1 = …
2)
Ø > 37 mm
c
b
Ø = 37 mm
a
1
1
B
A
1
