DEVICE NAME
The user can edit the default name “Solidyne
BTM641” in the cell phone Bluetooth settings.
Once paired, BLT LED switches to slow flashing
(each 2 seconds aprox) indicating "Bluetooth is
active".
Is no necessary to repeat this procedure for this
mobile phone. To pair another cell phone, repeat
the whole procedure.
Can not have two cell phones linked with the con-
sole at the same time.
RE-CONNECT A PAIRED DEVICE
1. Turn on the Bluetooth in MiniMIxer by press-
ing
“BLT”
until the LED lights (5 secs aprox).
The button will flash slowly.
2. Enable the Bluetooth in the cell phone. When
the cell phone notice that the connection has
been made the operator are ready to operate.
When the operator make or receive a call, the
audio is routed to the console.
RECONNECTION
In some mobiles the re-connection is not auto-
matic to the last used device. The user needs to
choose the Bluetooth device from a list to con-
nect it (the default name is Solidyne BTM641).
SET THE VOLUME
VERY IMPORTANT
At the cell phone, Bluetooth volume must be set at
maximum level in order to obtain a good reception
and to sure the best signal to noise ratio.
BLUETOOTH LEVEL
This value must be set with a real calling using the
Bluetooth.
The volume of the phone's speaker is inde-
pendent of the Bluetooth device.
If you change the phone's level during a call but the
Bluetooth is disconnected, you will only be changing
the volume for the phone's speaker, not the Bluetooth
level.
The Bluetooth level is stored into the cell phone's
memory. If you use another cell phone with the con-
sole, repeat this adjustment to set the volume to
maximum.
TURN OFF BLUETOOTH
To turn off the Bluetooth in MiniMIxer, press and
hold the button
BLT
until it ends to flash.
3.2.3 Use the Bluetooth link
1. Make sure that in the
"CELL Phone"
zone the
LEVEL control is set to zero and the CUE/
PGM button is in the position CUE (released).
2. Turn on Bluetooth on the console, pressing
and holding
BLT
(2 seconds approx) and re-
leasing as soon as it lights up. The button
keeps flashing slowly indicating that Blue-
tooth is active.
3.
Enable Bluetooth on the cell phone. If the cell
phone has already been paired with the con-
sole, the link is reestablished and in a few
seconds the cell phone is linked to the con-
sole.
INCOMING CALL
1. Always check that the CUE/PGM button is in
CUE (released) mode. Otherwise, if the button
is on PGM, answering the call could acciden-
tally go on the air.
2.
When a call incomes:
If Bluetooth is off on the
phone, you can answer and talk on the mobile,
and then activate Bluetooth to transfer the call
to the console.
But if Bluetooth is active on the phone, the call
can be answered from the console with a
short touch on the BLT button. In this condi-
tion, you can only speak through the Talkback
circuit of the console.
3. Once the calling is transferred to the MiniM-
ixer, the line receives return of PGM signal.
4. The operator can
talk with the caller by press-
ing the button TALK
on CELL Phone area, and
will hear the line on headphones.
5. To air the call, press the button CUE/PGM to
switch the line to PGM and set the level.
6. The call can be ended with a short touch on
the button BLT, or from the mobile phone.
7. It is also possible to resume the call on the
mobile, changing it from Headset mode to
Speaker mode.
Below shows a screenshot of a cell phone with
Android, in the case of Bluetooth enabled.
The example shows the "Headset" icon, which
transfers the call to the Bluetooth device when it
is turned on; and returns to the phone when it is
off. Other phone models can display two buttons;
a button with dropdown options; or other combi-
nations. Refer to the cell phone user manual.
MiniMIxer
broadcasting mixing console
Page 11
