Solid Build MODERNA 2 Скачать руководство пользователя страница 9

Страница: 9 / 15

GARDEN SHED

– MODERNA2 13 x 10 (1 1/8’’)

ASSEMBLY OF WALLS AND PILLARS

POSITION

DESIGNATION

DIMENSION (inch) QUANTITY

Window

24.56 x 29.48

Lower strip of double door
(horizontal)

55.51 x 2.95 x 2.59

Side strip of double door (vertical)

75.19 x 3.54 x 2.59

Top strip of double door (horizontal)

55.51 x 3.54 x 2.59

Double door

69.88 x 26.96

1+1

Gable

117.32 x 4.33 x 1.1

Pillar

79.53 x 4.33 x 4.88

Beam of pillar

130.71 x 5.51 x 1.73

Nicked front wall-board

168.90 x 6.49 x 1.1

Nicked top back wall-board

168.90 x4.33 x 1.1

Continue mounting walls with

intermediate side wall-boards

(

part no. 7),

short side

wall-boards

(

part no. 6) and

back wall-boards

(

part no. 5) till the 18

level of side

walls and slide in the

windows

(part no. 8) into the openings.

NOTE

. You can form window openings on any of the three walls, as low or as high as

you like.

Now, you can position the prefabricated

gable

(part no. 13).

Fasten

pillars

(part no. 14). Fix pillars with fasteners to your foundation or concrete

piers (fasteners aren’t included; use same as for shed anchoring). Fasten

beam of pillar

(part no. 15) with two 0.19x2.75” screws, 1 at each corner and place

nicked front wall-

board

(part no. 16). Fasten

nicked top back wall-board

(part no. 17) with two

0.19x2.75”screws, 1 at each corner.

Содержание MODERNA 2
















Результаты поиска

Содержание MODERNA 2

Отзывы:

Похожие инструкции для MODERNA 2

Бренды по названию

Популярные бренды

Solid Build MODERNA 2, Руководство по сборке

Результаты поиска

Содержание MODERNA 2

Отзывы:

Похожие инструкции для MODERNA 2

Бренды по названию

Популярные бренды