Solid Build MODERNA 2 Скачать руководство пользователя страница 14

Страница: 14 / 15

GARDEN SHED

– MODERNA2 13 x 10 (1 1/8’’)

INSTALLING FASCIA

POSITION

DESIGNATION

DIMENSION (inch)

QUANTITY

Front and back fascia-boards 170.39 x 8.66 x 0.74

Side fascia

130.70 x 8.66 x 0.74

Top front fascia

170.39 x 3.54 x 0.74

Top side fascia

128.66 x 3.54 x 0.74

Roof end boards

10.23 x 1.57 x 0.62

Roof end boards

35.24 x 1.57 x 0.62

Roof end boards

48.43 x 1.57 x 0.62

Before installing the chosen roofing, fix

fascia

(part no. 27, 28, 29 and 30) to the sides

of roofing with screws as shown in the image above.

Roof end boards

(part no. 31, 32

and 33) should be fixed to ends of roof boards under the front and back fascia. Attach
the

fascia flush with the roof boards

but covering the roof board ends - your roofing

material has to extend over them. Drip edge is optional but recommended. You may
install it as you start the roofing.

Only fix the top fascia

(part no. 29 and no. 30)

using bitumen roofing and

shingles.

Attach it on top of the finished roof to form a corner with the vertical fascia.

Содержание MODERNA 2
















Результаты поиска

Содержание MODERNA 2

Отзывы:

Похожие инструкции для MODERNA 2

Бренды по названию

Популярные бренды

Solid Build MODERNA 2, Руководство по сборке

Результаты поиска

Содержание MODERNA 2

Отзывы:

Похожие инструкции для MODERNA 2

Бренды по названию

Популярные бренды