Solectek skyway Скачать руководство пользователя | Manualshive

Страница: 33 / 52

background image

33

VLAN ID

: The ID should be set to match the VLAN ID used on your management PC. This setting

does not affect any other VLANs running on your network or the ability to pass VLAN traffic.

Warning:

Enabling Management Access via VLAN will

lock-out

HTTP and Telnet access if

attempting to connect from a PC without the proper VLAN configuration. Access to units with an
unknown VLAN configuration can be recovered through the use of Solectek’s

Recovery

utility

software on radios running recent revisions of software. Check with Solectek Support for details.

Ethernet Configuration

– This section allows users to configure the Ethernet port manually,

particularly for interfacing with older hardware. Solectek strongly recommends using auto-
negotiation default mode in most cases.

Video Support

– Enabling video support allows the user to activate Solectek Videocast mode, which

enhances the link capacity for video surveillance/monitoring network applications. For the details of
the Video mode, contact Solectek sales or refer to a separate documentation on video mode.

«
...
31
32
33
34
35
...
»

Содержание skyway





















































Отзывы:

Нет отзывов

Похожие инструкции для skyway

Бренд: Panasonic Страницы: 44

Бренд: Panasonic Страницы: 44

SAHE200 - RECEIVER

Бренд: Panasonic Страницы: 25

PressIT TY-SB01WP

Бренд: Panasonic Страницы: 25

Бренд: Xtrend Страницы: 65

Бренд: Cadillac Страницы: 102

Personal PA Receiver PPA R35N

Бренд: Williams Sound Страницы: 6

Бренд: Ten-Tec Страницы: 147

Бренд: Icom Страницы: 116

Бренд: X10 Страницы: 9

Satellite Television

Бренд: Dish Network Страницы: 134

Бренд: CAME Страницы: 24

Бренд: Kessler Engineering Страницы: 8

Бренд: Easy wave Страницы: 8

Бренд: F&U Страницы: 23

Бренд: Extron electronics Страницы: 37

Бренд: HobbyKing Страницы: 6

Бренд: Power Acoustik Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды