Sole Diesel 10 GS/GSC Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 94

background image

Systems and scheduled

maintenance

Solé, S.A. C-243 b, km 2 · 08760 Martorell (Barcelona) ·Tel. +34 93 775 14 00 · www.solediesel.com · [email protected]

28

Marine Diesel gensets. Operator’s Manual.

5.5.

Fuel System

Circuit description

The fuel system is based on a fuel feed pump and an in-line mechanical injection pump.

Fuel specifications

Use ASTM Diesel fuel No.2-D for the best genset performance, to prevent genset damage.

Never use kerosene, heavy Diesel fuel or bioDiesel. It is essential to use clean and filtered Diesel oil.

The use of Diesel oil that not complies with the technical specifications may affect warranty

coverage and cause serious damage in the injection system and internal genset components.

Maintenance task. Fuel level inspection

Periodically, it is necessary to check the fuel level to assure the operation of the genset. On

top of that, if fuel pump sucks air when the fuel level is lower than pump suction, it could break.

Whenever possible, keep the fuel tank full. The temperature changes may cause

condensation of the damp air present in the tank and this water accumulates at the bottom. It can
cause an increase of corrosion or an impossibility of starting the genset if this water is aspired by the
fuel pump.

Maintenance task. Fuel tank clean

The fuel impurities could obstruct the suction pump. For this reason, drain out the content of

the fuel tank to remove condensate and any foreign material. Then, wash the tank with fuel and refill
it.

Maintenance task. Water separator filter purge

The fuel system has to have a water separator filter (supplied as accessory) to

avoid the inlet of water in the fuel circuit. According to the maintenance plan it is
necessary to purge the filter to eliminate water periodically. This is the procedure:

1.

Loosen the bottom nut to eliminate water.

2.

Shut it off again.

PIECE ELEMENT

1

Fuel injection nozzle

2

Fuel injection pipe

3

Fuel leak-off pipe

4

Injection pump

5

Feed fuel pump

6

Fuel filter

7

Tank (supplied as accessory)

8

Fuel decanting filter (supplied
as accessory)

9

Fuel intake pipe (supplied
accessory)

«
...
27
28
29
30
31
...
»

Содержание 10 GS/GSC































































































Отзывы:

Нет отзывов

Похожие инструкции для 10 GS/GSC

DVDLS91 - PORTABLE DVD PLAYER

Бренд: Panasonic Страницы: 32

Бренд: Samsung Страницы: 32

Бренд: Samsung Страницы: 32

Бренд: Harbor Freight Tools Страницы: 32

Бренд: Conceptronic Страницы: 11

Бренд: Wacker Neuson Страницы: 60

Бренд: Neilsen Страницы: 40

Бренд: Simoco Страницы: 50

Бренд: Powermate Страницы: 72

Бренд: Wacker Neuson Страницы: 46

Бренд: QFX Страницы: 11

FG085 Function Generator

Бренд: JYE Tech Страницы: 2

Бренд: Lincoln Electric Страницы: 22

Бренд: Lafayette Страницы: 7

Бренд: CAMPAGNOLA Страницы: 70

Бренд: Horizon Fuel Cell Technologies Страницы: 53

Бренд: AWA Страницы: 37

Бренд: Philips Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды