Sole Diesel 10 GS/GSC Скачать руководство пользователя страница 38

Страница: 38 / 94

Systems and scheduled

maintenance

Solé, S.A. C-243 b, km 2 · 08760 Martorell (Barcelona) ·Tel. +34 93 775 14 00 · www.solediesel.com · [email protected]

Marine Diesel gensets. Operator’s Manual.

Battery

The minimum recommended capacity is from 55-120 Ah. However, this value serves as a

general reference since it relates to the maximum intensity it can offer for starting the generator set.

The connection of the battery for a standard engine:

•

Positive battery is connected to the starter.

•

Negative battery is connected to the relay support.

The connection of the battery for an earth isolated engine.

•

Positive battery is connected to the starter.

•

Negative battery is connected to the bipolar relay.

Circuit protection

AC Breaker interrupts the genset output in the event of an overload or short circuit. The

nominal current is indicated in the following table:

Maintenance task. Incandescent glow plug inspection

Loosen nuts, and then remove connection plate and
glow plug.

If the glow plug glows red when the positive (+) wire is
connected to the portion A with the portion B
grounded, the plug can be used.

Genset model

Battery capacity (Ah)

12V

24V

8 GTC / 10 GTAC / 7 GSC / 8 GSAC

11 GTC / 14 GTAC / 10 GSC / 12 GSAC / 17 GTC / 20

GTAC / 14 GSC / 17 GSAC

25 GTC/30 GTAC/ 20 GSC/25 GSAC

Model

Current (A)

8 GTC /10 GTAC

20 (Delta) / 10 (Star)

7 GSC / 8 GSAC

11 GTC / 14 GTAC

25 (Delta) / 16 (Star)

10 GSC / 12 GSAC

17 GTC / 20 GTAC

40 (Delta) / 25 (Star)

14 GSC / 17 GSAC

25 GTC / 30 GTAC

63 (Delta) / 40 (Star)

20 GSC / 25 GSAC

100

Rated voltage - Current 12 V

9,7-10,5 A

Glowplug

Nut

Connection board

Содержание 10 GS/GSC































































































Результаты поиска

Содержание 10 GS/GSC

Отзывы:

Похожие инструкции для 10 GS/GSC

Бренды по названию

Популярные бренды

Sole Diesel 10 GS/GSC, Руководство оператора

Результаты поиска

Содержание 10 GS/GSC

Отзывы:

Похожие инструкции для 10 GS/GSC

Бренды по названию

Популярные бренды