Solaris LOCOR Скачать руководство пользователя страница 7

Страница: 7 / 9

The cover is designed to be mounted on either left or right side of the

housing. Manufacturing setting is left-side mounting. To change to right-side

mounting, follow steps 1 - 5:

Step 1: Remove Hinge Pins

(Top & Bottom)

First remove the e-clips at the end of the pins. Then remove the pins

Step 2: Remove the

Removable

Hinges

(Top & Bottom)

First remove the screws. Then remove

the hinges.

Step 3: Remove the Door Seal Plug

Flex one of the legs to push the door plug out.

Step 4: Remove the Lock

First remove

the

screws. Then remove the

lock.

Step 5: Reverse step

1 - 4

and switch side when install the components back

on the cover. Note that the Hinges and Pins should be installed on the same

side that the cover is desired to be mounted on. The Lock should be installed

on the opposite side of the Hinges. And the Plug should be installed on the

same side as the Hinges.

See Figure

for more details.

Bottom Hinge

Removable Hinge

E-clip

Top Hinge

E-clip

Removable Hinge

Lock

Screw

Lock

Door

Seal

Plug

Flex one of

the three legs

to push the

plug out

Screw

8778002

Released January

201

CHANGING MOUNTING SIDE OF COVER

Figure

Содержание LOCOR










Результаты поиска

Содержание LOCOR

Отзывы:

Похожие инструкции для LOCOR

Бренды по названию

Популярные бренды

Solaris LOCOR, Руководство пользователя

Результаты поиска

Содержание LOCOR

Отзывы:

Похожие инструкции для LOCOR

Бренды по названию

Популярные бренды