Solaris KIP4550E10, Руководство пользователя

Страница: 38 / 44

38
off button for three seconds to save and exit. Afterwards, the unit
will continue to operate normally.
Adaptive Start feature
This feature can only be used for the weekly program. When the unit
is set to automatic power-on without this setting, it switches on at the
designated time and provides heating. However, it will take some
time for the unit to reach the designated temperature. This causes
inconvenience for the user due to the delay in heating. The adaptive
start feature is designed to prevent this. If this feature is activated,
your unit will start heating at a time depending on the difference
between the ambient temperature and the desired temperature when
the designated automatic power-on time is close. This feature ensures
that the ambient temperature is at the desired temperature at the
designated time. (The Adaptive Start Feature does not guarantee
that the ambient temperature will be exactly at the designated
temperature at the time set for the program. Because the environment
in which the device is placed has many factors that make heating
difficult in practice such as thermal insulation, doors and windows
left open, a very large volume, and heat leakage.)
The instructions below must be followed in order for this feature to
work with maximum efficiency:
1. Selecting the power according to the space where the unit is placed,
2. Keeping the doors and windows closed and preventing other leaks,
if any. 3. Ensuring thermal insulation in the environment where the
unit is placed, 4. Setting the adaptive start parameters accurately.
Default values: “P 01” : 20 min and “P 02”: 5 hours. At least one of
these parameters must be set to 0 to deactivate this feature.
Adaptive Start parameters
This feature has two parameters. The first parameter is the duration
for early automatic power-on per degree. (This value is set with the
parameter “P 01”.) This duration is measured in minutes. It can be
set from 0 to 40 minutes. The unit calculates how early it should
start heating by multiplying this parameter value by the difference
between the current ambient temperature and the target temperature.
For example, if the unit is set to switch on at 09.00 at 23 degrees
Celsius in the weekly program, if the ambient temperature is 19
degrees Celsius and if the parameter is set to 20 minutes per degree
Celsius, the time for the unit to start heating is calculated using the
following formula:
Heating Time = Program Time - (Target Temperature - Current
Temperature) x Parameter Value = 09:00 – (23 – 19) x 20
= 09:00 – 80 min. (1 hour 20 min.) The time to start heating = 07:40.
So, the unit starts to heat 80 minutes (1 hour 20 minutes) earlier than
the designated time.
If the unit is on, if the adaptive start feature is activated and if the unit
switches on earlier to start heating, “A 23” will appear on the display
when you press and hold the plus or minus button for three
seconds. The number 23 represents the target temperature value that
you set and it will display your designated temperature.
If the plus or minus button is pressed while the adaptive start
is deactivated, the unit will only display “23”.
The other parameter is to set a limit for the early automatic power-on
time. Even if the early power-on time calculated above exceeds this
parameter value, the unit will not start heating before the time set
with this parameter. (This value is set with the parameter “P 02”.)
This parameter is measured in hours. It can be set from 0 to 5 hours.
Adaptive Start parameter Setting
(“p 01” and “p 02”)
Switch off the heater using the power switch on the side. Switch on
the heater while pressing and holding the menu button “ASEt”
appears on the heater’s display for approximately six seconds. “P 01”
will start flashing on the display. The plus and minus buttons
can be used to switch to the other parameter (“P 02”). Press the
menu button to change the value of the desired parameter. The
parameter value will appear on the display, and the desired value can
be set using the plus and minus buttons. If you press the menu
button again, you can change the parameter again. Press and hold
the on/off button for three seconds to save your settings and exit.
Afterwards the unit will continue to operate normally.