manualshive.com logo in svg

Sofar 3000TLM-G2, Руководство пользователя

Поделиться
Скачать
Sofar 3000TLM-G2 Скачать руководство пользователя страница 9

SOFAR 3K~6KTLM-G2

User manual

Copyright © Shenzhen SOFARSOLAR Co., Ltd

- 4 -

Before any repair work, turn OFF the AC circuit breaker

between the inverter and electrical grid first, then turn OFF the DC

switch.

After turning OFF the AC circuit breaker and DC switch, wait

for 5 minutes at least before carrying out any maintenance or repair

work.

Danger

Inverter should work again after removing any faults. If you

need any repair work, please contact with the local authorized

service center.

Can’t open the internal components of inverter without

authorized. Shenzhen SOFARSOLAR Co., Ltd. does not take any

responsibility for the losses from that.

Attention

EMC / noise level of inverter

Electromagnetic compatibility (EMC) refers to that one electrical equipment

functions in a given electromagnetic environment without any trouble or error, and
impose nonacceptable effect upon the environment. Therefore, EMC represents the
quality characters of an electrical equipment.
The inherent noise-immune character: immunity to internal electrical noise.
External noise immunity: immunity to electromagnetic noise of external system.
Noise emission level: influence of electromagnetic emission upon environment.

Electromagnetic radiation from inverter may be harmful to

health!

Please do not continue to stay around the inverter in less than 20

cm when inverter is working.

Danger

1.2. Symbols and signs

Caution of burn injuries due to hot enclosure!

You can only touch the screen and pressing key of the inverter

while it’s working.

Caution

PV array should be grounded in accordance to the requirements

of the local electrical grid operator!

We suggest that all PV module frames and inverter are reliably

grounded to protect the PV system and personnel security.

Attention

Содержание 3000TLM-G2





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды