Sofar solar 100KTL Скачать руководство пользователя страница 70

Страница: 70 / 80

75-136KTL

User manual

- 66 -

permanent failure

ID135

PermIacUnba

lance

Permanent failure

of unbalanced

output current

ID137

PermInCfgEr

ror

Input mode setting

error permanent

failure

Check the PV input mode (parallel/independent

mode) Settings for the inverter. If not, change

the PV input mode.

ID138

PermDCOCP

Instant

Input overcurrent

permanent fault

ID139

PermHwDCO

Input hardware

overcurrent

permanent failure

Internal faults of inverter, switch OFF inverter,

wait for 5 minutes, then switch ON inverter.

Check whether the problem is solved.

If no, please contact technical support.

ID140

PermRelayFa

Permanent relay

failure

ID141

PermBusUnb

alance

Bus voltage

unbalanced

permanent failure

ID142

PermSpdFail(

DC)

PV surge protection

ID143

PermSpdFail(

AC)

Grid surge

protection

ID145

USBFault

USB fault

Check the USB port of the inverter

ID146

WifiFault

Wifi fault

Check the Wifi port of the inverter

ID147

BluetoothFau

Bluetooth fault

Check the bluetooth connection of the inverter

ID148

RTCFault

RTC clock failure

Internal faults of inverter, switch OFF inverter,

wait for 5 minutes, then switch ON inverter.

Check whether the problem is solved.

If no, please contact technical support.

ID149

CommEEPR

OMFault

Communication

board EEPROM

error

ID150

FlashFault

Communication

board FLASH error

ID152

SafetyVerFau

The software

version is

inconsistent with

the safety version

ID153

SCILose(DC)

SCI communication

error (DC)

ID154

SCILose

(AC)

SCI communication

error (AC)

ID155

SCILose

(Fuse)

SCI communication

error (Fuse)

ID156

SoftVerError

Inconsistent

software versions

Contact for technical support and software

upgrades.

ID161

ForceShutdo

Force shutdown

The inverter is performed a forced shutdown

ID162

RemoteShutd

Remote shutdown

The inverter is performed a remote shutdown.

Содержание 100KTL

















































































Результаты поиска

Содержание 100KTL

Отзывы:

Похожие инструкции для 100KTL

Бренды по названию

Популярные бренды

Sofar solar 100KTL, Руководство пользователя

Результаты поиска

Содержание 100KTL

Отзывы:

Похожие инструкции для 100KTL

Бренды по названию

Популярные бренды