Sofar solar 100KTL Скачать руководство пользователя страница 38

Страница: 38 / 80

75-136KTL

User manual

- 34 -

RS485

Modbus/DRMs

RS485/DRMs

RS485 Communication

port/DRMs port

AC output

terminals

AC output terminal

Grounding

Connecting terminal of the

ground, choose at least one for

grounding connection

5.3. Grounding Connection (PE)

Connect the inverter to the grounding electrode using ground cable.

SOFAR 75-136kW is a transformerless inverter which requires the

positive pole and negative pole of the PV array are NOT grounded.

Otherwise, it will cause inverter failure. In the PV system, all

non-current-carrying metal parts (such as mounting frame, combiner

box enclosure, etc.) should be connected to earthed.

Note

Preparation: prepare the grounding cable (recommend 16mm² yellow-green
outdoor cable and M8 OT Terminal)
Procedure:

Step 1

: Remove the insulation layer with an appropriate length using a wire stripper

shown as figure 5-2.

Figure 5-2 Grounding connection instruction

（

）

Note

：

the length of L2 should 2~3mm higher than L1.

Step 2

: Insert the exposed core wires into the OT terminal and crimp them by using

a crimping tool, as shown as figure 5.3. Recommend using OT terminal: OT M6,

Cable: ≥6mm

Содержание 100KTL

















































































Результаты поиска

Содержание 100KTL

Отзывы:

Похожие инструкции для 100KTL

Бренды по названию

Популярные бренды

Sofar solar 100KTL, Руководство пользователя

Результаты поиска

Содержание 100KTL

Отзывы:

Похожие инструкции для 100KTL

Бренды по названию

Популярные бренды