background image

29

Flex Plow Operation and Maintenance Manual

Maintenance

Flex Plow Maintenance

AVOID SERIOUS INJURY OR DEATH

Always  turn  off  and  lockout  power  before
servicing the attachment.

AVOID SERIOUS INJURY OR DEATH

Always  disconnect  hydraulic  connections
between  the  attachment  and  the  machine
before performing any type of maintenance
to the Flex Plow.

AVOID SERIOUS INJURY OR DEATH

Securely  block  up  the  attachment  before
working underneath.

Cutting Edge Replacement

NOTE: Replace or flip the bolt-on cutting edge

when  it  wears  within  1/2”-  3/4”  of  the
bolt  head  securing  it  to  the  trip-edge.
Replace  only  with  genuine  SnowWolf
cutting edge and hardware.

1. Park the machine on a level surface with the

Flex Plow properly attached.

2. Lower  the  Flex  Plow  approximately  three  to

four inches off the ground.

3. Engage the parking brake.

4. Shut  off  the  machine's  engine,  remove  the

ignition  key  (if  equipped),  wait  for  all  moving
parts to come to a stop and relieve all pressure
in the hydraulic lines.

5. Block and/or support the Flex Plow with proper

lifting device capable of sufficiently supporting
the unit's weight.

6. Disconnect hydraulic connections between the

attachment and the machine.

NOTE: The cutting edge and hardware 

quantity will vary depending upon the 
Flex Plow model.

7. Block  the  cutting  edge,  remove  the  fasteners

and remove the cutting edge.

NOTE:  Be  cautious  as  the  cutting  edge  and

hardware may be sharp.

8. Repeat procedure for the cutting edge.

9. Properly dispose of the old cutting edges and

install the new cutting edge’s by reversing the
steps listed here.

NOTE: Replace worn or damaged fasteners as

needed.

Содержание Flex Plow





















































Отзывы: