16
I) The 0º intense-jet nozzle (orange) is an extremely
powerful nozzle that delivers a high-pressure, pencil-
point jet stream. It is used to cut heavy dirt deposits
in a small, concentrated area. It is ideal for dissolving
stubborn substances, like tar and grease spots on
concrete, or for removing caked mud from equipment.
Use this nozzle to clean hard-to-reach areas including
the facades of 2-story buildings or the undersides of
lawn mowers and tractors.
NOTE: Care should be used when choosing the
right nozzle to avoid permanently gouging wood or
damaging fragile surfaces.
II) Use the 15º fan-tip nozzle (yellow) for intense cleaning
jobs on hard surfaces. Applications include stripping
paint, removing oil stains, grease, heavy mildew stains,
and rust from steel. This nozzle should only be used in
areas that can withstand the high-pressure from this
nozzle.
III) Use the 25º fan-tip nozzle (green) to clean home
siding, brick patios, wood decks, driveways, or
sidewalks. When using this nozzle, test a small area
first to avoid surface damage.
IV) Use the 40º wide-spray tip nozzle (gray) to clean items
such as cars, trucks, boats, patio furniture, or lawn
equipment.
7. Lock the bucket with water on the base unit or connect
the base unit with a water supply. Start at the top of the
area to be rinsed and work your way down, making sure
to overlap your strokes.
m
IMPORTANT!
NEVER USE:
• Bleach, chlorine products, and other corrosive chemicals
• Liquids containing solvents (e.g. paint thinners, gasoline, oils)
• Tri-sodium phosphate products
• Ammonia products
• Acid-based products
These chemicals will harm the unit and will damage the
cleaning surface.
Shutting Down
1. Press the On/Off button on the control panel.
2. Pour the remaining water out from the bucket or turn off
the water source.
3. Hold the trigger to release water pressure.
4. If using the base unit directly, disconnect the garden hose
from the water inlet on the base unit.
5. Disconnect the high-pressure hose connection on the
trigger gun handle.
6. Release the trigger and lock the gun safety lock.
m
WARNING!
Turn off the water supply and squeeze the
trigger to depressurize the unit. Failure to do so could result in
personal injury due to discharge of high-pressure water.
Taking a Break
If you are taking a break of five minutes or more between
cleaning tasks:
1. Lock the gun safety lock.
2. Push the On/Off button to stop the machine.
Storage
m
CAUTION!
Always store your pressure washer in a
location where the temperature will not fall below 32ºF (0ºC).
The pump in this machine is susceptible to permanent damage
if it freezes. FREEZE DAMAGE IS NOT COVERED BY THE
WARRANTY.
• Store the pressure washer indoors in a dry, covered area
where it is not subject to adverse weather conditions.
• It is important to store this product in a frost-free area.
• Always empty water from all hoses, the pump, the soap
dispense attachment and the bucket before storing.
m
CAUTION!
The use of a pump protector is
recommended to prevent cold weather damage during storage
over the winter months.
Winte Long-Term Storage
If you must store your pressure washer in a location where
the temperature falls below 32ºF (0ºC), you can minimize the
chance of damage to your machine by utilizing the following
procedure:
• Disconnect all water connections.
• Turn on the machine for a few seconds until the remaining
water in the pump exits. Turn off immediately.
• Do not allow the high-pressure hose to become kinked.
• Store the machine and accessories in a room that does
not reach freezing temperatures.
• Do not store near a furnace or other sources of heat that
may dry out the pump seals.
15º
SOA
P
25º
40º
0º
Fig. 25
