SNOWJOE MAX SJ803 Скачать руководство пользователя страница 18

Страница: 18 / 20

Troubleshooting

Problem

Cause

Remedy

Excessive vibration

1. Loose parts or damaged auger.

1. Stop the engine immediately

and disconnect the spark plug

wire. Tighten all bolts and nuts.

If vibration continues, have the

unit serviced by an authorized

service dealer.

Unit fails to propel itself

1. Auger control cable out of

adjustment.

2. Drive belt loose or damaged.

1. Adjust auger control cable.

Refer to Maintenance and

Adjustments Section.

2. Replace drive belt. Refer to

the Maintenance and

Adjustments section.

Augers continue to rotate 1. Auger control cable out of

adjustment.

1. Adjust auger control cable as

shown in Maintenance and

Adjustments section.

Unit fails to discharge

snow

1. Chute assembly clogged.

2. Foreign object lodged in auger.

3. Auger control cable in need of

adjustment.

1. Stop engine and disconnect

spark plug wire. Clean chute

and inside of auger housing

with clean-out tool or a stick.

2. Stop engine immediately and

disconnect spark plug wire.

Remove object from auger.

3. Adjust auger control cable.

Refer to Maintenance and

Adjustments section.

SJ_803_MANUAL ENG_R_Layout 1 9/2/10 2:23 PM Page 18

Содержание MAX SJ803





















Результаты поиска

Содержание MAX SJ803

Отзывы:

Похожие инструкции для MAX SJ803

Бренды по названию

Популярные бренды

SNOWJOE MAX SJ803, Руководство оператора

Результаты поиска

Содержание MAX SJ803

Отзывы:

Похожие инструкции для MAX SJ803

Бренды по названию

Популярные бренды