background image

9

Discharge Chute Assembly

1. 

Use the hex key to remove the 4 nuts from the gear plate. 

Keep them on the side (Fig. 3).

2. 

Place the discharge chute assembly onto the gear plate, 

aligning the 4 holes in the gear plate, and push down until 

the chute is flush and flat against the housing (Fig. 4).

3. 

Using the 4 nuts, secure the discharge 

chute assembly to 

the gear plate (Fig. 4).

4. 

Press the chute deflector trigger to raise or lower the 

chute deflector to the desired height of the snow stream 

(Fig. 5).

Chute Clean-Out Tool

The chute clean-out tool is fastened to the top of the auger 

housing with a mounting clip (Fig. 6).

Skid Shoes Adjustment

Position the skid shoes based on surface conditions. Adjust 

upward for hard-packed snow. Adjust downward when 

operating on gravel or crushed rock surfaces.

The snow blower skid shoes are adjusted at the factory for 

shipping purposes. Adjust them downward, if desired, prior to 

operating the snow blower.

m

WARNING! 

It is not recommended that you operate this 

snow blower on gravel as it can easily pick up and throw loose 

gravel, causing personal injury or damage to the snow blower 

and surrounding property.

1. 

For close snow removal on a smooth surface, raise skid 

shoes higher on the auger housing. Allow 1/8 in. (3 mm) 

between scraper blade and hard, smooth surface(s).

2.  Use a middle or lower position when the area to be 

cleared is uneven, such as a gravel driveway. 

Allow  

1-1/4 in. (30 mm) between scraper blade and uneven or 

gravel surfaces.

NOTE: If you choose to operate the snow blower on a 

gravel surface, keep the skid shoes in position for maximum 

clearance between the ground and the scraper blade.

To adjust the skid shoes:

3. 

Loosen the 4 hex nuts (2 on each side). Move skid shoes 

to desired position (Fig. 7).

Fig. 3

Nut

Hex key

Gear plate

Fig. 4

Nuts

Gear plate

Discharge chute 

assembly

Fig. 5

Chute 

deflector 

trigger

Fig. 6

Chute clean-out tool

Fig. 7

Skid shoe

Hex nut

Содержание iON8024-XRP





























Отзывы: