background image

3

m

Safety decals and instructions are easily visible to

the operator and are located near areas of potential

danger. Lost or damaged decals should be replaced.

622U1/623U1-2134

622U1/623U1-2135

622U1/623U1-2136

k.

When work is completed –

Disconnect the snow 

thrower from the power source when not in use, when 

changing accessories, and before performing any 

maintenance function.

l.

Store safely –

Store snow thrower indoors in a dry

area between uses. Keep in a locked area, where 

children and unauthorized users cannot gain access.

Do not store the machine while it is still connected

to the power source. It may cause damage and injury.

Safety and Instruction Decals 

622U1/623U1-2137

TO START

Press Switch

Squeeze Bar

TO STOP

Release Bar

PARA PONER 

EN MARCHA

Presione el botón 

del interruptor

Exprima la barra 

de la manija

PARA APAGAR

Suelte la barra 

POUR DÉMARRER

Appuyez sur 

l'interrupteur 

Serrez la poignée

POUR ARRÊTER

Relâchez la poignée

¡ADVERTENCIA!

W A R N I N G !

Electric shock can cause serious injury

or death. To avoid electric shock: 

DO

NOT USE SNOW THROWER IF WIRE
INSULATION IS DAMAGED. READ
ASSEMBLY INSTRUCTIONS AND
OPERATOR’S MANUAL.

Una descarga eléctrica puede causar

lesiones graves o la muerte. Para evitarla:

NO UTILIZAR EL LANZADOR DE
NIEVE SI EL AISLANTE DEL CABLE  
ESTÁ DAÑADO. LEER LAS
INSTRUCCIONES DE ENSAMBLAJE
Y EL MANUAL DEL OPERARIO. 

Un choc électrique peut provoquer des

blessures graves voire mortelles. Pour éviter

les chocs électriques : N'UTILISEZ PAS LA

SOUFFLEUSE À NEIGE SI L'ISOLATION

D'UN FIL EST ENDOMMAGÉE. LISEZ

LES INSTRUCTIONS DE MONTAGE ET

LE MANUEL DE L'UTILISATEUR.

AVERTISSEMENT !

m.

Maintain for safety and longevity –

Check for

misalignment or binding of moving parts, breakage
of parts, and any other conditions that may affect the 

unit!s operation. If damaged, repair or replace the 

damaged part before use. Use only those replacement 

parts made for your model. When replacing any 

parts, you must strictly observe the instructions and 

procedures described in this manual. Special care 

should be paid to any rubber parts, since these parts 

may increase the engine load and decrease its 

mechanical power if damaged.

DOUBLE INSULATED:

When servicing, use only identical

replacement parts.

SNOW JOE ULTRA MODEL 622U1

120 VAC  60 HZ  13 AMP

Made in China
SNOW JOE ULTRA MODELO 622U1 

120 VAC  60 HZ  13 AMP

Fabricado en China
SNOW JOE ULTRA MODÈLE 622U1

120 VCA 60 HZ  13 AMP

Fabriqué en Chine

D A N G E R

m

DANGER 

Do not use hands to unclog chute. Stop motor before removing debris. Do not walk in front of 

running machine. Do not direct discharge at bystander.

CAUTION 

Use for snow removal only.

WARNING 

To reduce the risk of electric shock, replace damaged cord immediately.

PELIGRO 

No emplee las manos para desatascar la tolva. Pare el motor antes de sacar el material atascado. 

No camine delante de la máquina en funcionamiento. No descargue directamente sobre los transeúntes.

ADVERTENCIA 

De uso exclusivo para remover la nieve.

ADVERTENCIA 

Para prevenir el riesgo de una descarga eléctrica, cambie el cable dañado inmediatamente.

DANGER 

Ne pas déboucher le conduit d!éjection à la main. Arrêter le moteur avant d!ôter tout debris. 

Ne pas se mettre devant une machine en marche. Ne pas diriger le jet d!éjection de neige vers quelqu!un.

ATTENTION 

N!utiliser que pour ôter la neige.

AVERTISSEMENT 

Afin de prévenir le risque d!électrocution, remplacer immédiatement le cordon 

électrique abîmé.

DOBLE AISLAMIENTO: 

Al darle servicio, use solo 

piezas idénticas.

DOUBLE ISOLATION: 

lors de l!entretien, n!employer que des

pièces de rechange identiques.

Read operator!s manual for operating and safety instructions. 

Replacement manual available by sending model and serial numbers to: 

Snow Joe, LLC, 86 Executive Avenue, Edison, NJ 08817, or visit www.snowjoe.com
Lea el manual de instrucciones de seguridad y operación. 

Tenemos disponible manuales de reemplazo si envía el número de modelo y número de serie a:

Snow Joe, LLC, 86 Executive Avenue, Edison, NJ 08817, o visite www.snowjoe.com
Lire le manuel pour connaître le mode d!emploi et les prescriptions de sécurité.

Manuel de rechange disponible sur envoi du numéro de modèle et du numéro de série à : 

Snow Joe, LLC, 86 Executive Avenue, Edison, NJ 08817, ou visiter le site www.snowjoe.com

CONFORMS TO UL STD.1090

CERTIFIED TO CAN/CSA

STANDARD C22.2 NO. 147-M90 
CONFORME A LA NORMA UL 1090

CERTIFICADO POR CAN/CSA

NORMA C22.2 NO. 147-M90
CONFORME À LA NORME UL 1090

CERTIFIÉ POUR CAN/CSA

STANDARD C22.2 NO. 147-M90 

SJ622U1_MANUAL_ENG REV_Document 1  9/2/10  2:32 PM  Page 3

Содержание 622U1

















Отзывы: