Snapper VCP216012RV Скачать руководство пользователя | Manualshive

Страница: 28 / 28

background image

28

Safety Instructions & Operator’s Manual for

21” STEEL DECK
WALK MOWERS
COMMERCIAL MODEL
SERIES 12

IMPORTANT

Snapper products are built using engines that meet or exceed all applicable emissions requirements on
the date manufactured. The labels on those engines contain very important emissions information and
critical safety warnings. Read, Understand, and Follow all warnings and instructions in this manual, the
engine manual, and on the machine, engine and attachments. If you have any questions about your
Snapper product, contact your local authorized Snapper dealer or contact Snapper Customer Service at
Snapper, McDonough, GA. 30253. Phone: (1-800-935-2967).

WARNING:

The engine exhaust from this product contains chemicals known to the State
of California to cause cancer, birth defects or other reproductive harm.

COPYRIGHT © 1999
SNAPPER INC.
ALL RIGHTS RESERVED

MANUAL No. 3-5725 (REV. 2, 9/2/99)

«
...
26
27
28

Содержание VCP216012RV





























Отзывы:

Нет отзывов

Похожие инструкции для VCP216012RV

Бренд: Yard-Man Страницы: 16

MULTICLIP Pro 51 S

Бренд: Stiga Страницы: 10

69168 - Turfcat T628D

Бренд: Jacobsen Страницы: 59

Бренд: MTD Страницы: 20

Бренд: Jacobsen Страницы: 98

Бренд: Gardena Страницы: 11

Бренд: Wizard Страницы: 48

Бренд: Yard-Man Страницы: 12

Бренд: Worksaver Страницы: 40

Super Surfer II GSKA1948S

Бренд: Great Dane Страницы: 78

Бренд: Toro Страницы: 24

Бренд: Craftsman Страницы: 24

Бренд: Craftsman Страницы: 28

Бренд: Craftsman Страницы: 24

Бренд: Craftsman Страницы: 22

Бренд: Craftsman Страницы: 22

Бренд: Craftsman Страницы: 27

Бренд: Craftsman Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды