Snapper VCP216012RV Скачать руководство пользователя | Manualshive

Страница: 11 / 28

background image

11

Section 3 - MAINTENANCE

WARNING

DO NOT attempt any maintenance, adjustments or
service with engine and blade running. STOP engine
and blade. Disconnect spark plug wire and secure
away from spark plug. Engine and components are
HOT. Avoid serious burns, allow sufficient time for
all components to cool. Wear heavy leather gloves
when handling or working around cutting blades.
Blades are extremely sharp and can cause severe
injury.

3.3 SERVICE - ANNUALLY
Perform all maintenance as described in the “Service
Schedule” section of this manual.

3.3.1. Engine
Service engine according to engine owner’s manual.
3.3.2. Air

Filter

Refer to engine owner’s manual for service
instructions.
3.3.3. Engine

Oil

Refer to engine owner’s manual for service
instructions.

3.4 STORAGE

PROCEDURE

Refer to the Engine Owner’s Manual for directions
regarding engine storage preparations. Prepare the
mower for “end of season” storage as follows:

1.  Drain fuel from fuel tank and let engine run until
all fuel is out of the carburetor.
2.  Disconnect and remove the spark plug wire
away from spark plug before any other
preparations are made!
3. Tape all openings closed to prevent spraying
water into exhaust or air intakes during washing.
4.  Tilt mower up on its rear wheels and thoroughly
clean the underside of the deck. Do not tilt mower
with spark plug or carburetor down. Scrape away
any accumulation of grass with a putty knife and or
wire brush.
5.  Lubricate all exposed metal with a light coating
of oil to prevent corrosion.
6.  On self-propelled models disconnect transfer rod
clip and remove ground speed control rod before
folding handles.
7.  Loosen handle knobs. Carefully fold the handles
forward, “flexing” the control cables to prevent cable
damage.
8. Store the mower in a shed or other dry area,
protected from weather.

«
...
9
10
11
12
13
...
»

Содержание VCP216012RV





























Отзывы:

Нет отзывов

Похожие инструкции для VCP216012RV

Бренд: Jacobsen Страницы: 114

MULTICLIP Pro 51 S

Бренд: Stiga Страницы: 10

Бренд: Meec tools Страницы: 30

Бренд: Stihl Страницы: 120

Wheel Horse XL 320 71199

Бренд: Toro Страницы: 40

Бренд: Racing Страницы: 21

Бренд: Brute Страницы: 44

Бренд: Weed Eater Страницы: 48

Бренд: SaMASZ Страницы: 36

Бренд: COMPANION Страницы: 76

Бренд: Poulan Pro Страницы: 60

Бренд: Lastec Страницы: 68

Бренд: Challenge Страницы: 19

Бренд: Spear & Jackson Страницы: 24

Бренд: MASSEY FERGUSON Страницы: 31

Бренд: MTD Страницы: 31

Бренд: bannerman Страницы: 11

REVOLT BRV36FX691

Бренд: Bad Boy Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды