Snapper SLT23460 (7800342) Скачать руководство пользователя страница 32

Страница: 32 / 48

How to Remove the Mower Deck (46 & 52” Models)

1. Push the

PTO switch

down to the DISENGAGE position.

2. Open the deck level position cover, and move the

deck

lift lever

to the level adjustment position (Figure 34).

WARNING: The deck lift lever is spring loaded.
Make sure the deck lift lever is locked in the LEVEL
ADJUSTMENT position.

3. Remove the hair pins and the washers from the

adjuster arms

(Figure 35). See illustrations “C” and

“D”.

4. Remove the hair pins and washers from the

suspension links

. See illustrations “A” and “B”.

Figure 34: Deck lift lever

A - Deck level position cover (partially hidden)
B - Deck level adjustment position

5. Disconnect the

front hanger

from the axle support. See

illustration “E”.

6. Remove the

mower drive belt

from the

clutch pulley

See illustration “F”.

7. Pull the mower deck away from the right side of the

unit.

8. To operate without the mower deck, move the deck lift

lever to the TOP position.

How to Install the Mower Deck (46 & 52” Models)

1. Push the mower deck under the right side of the unit.

2. Put the

mower drive belt

around the

clutch pulley

Make sure the “V” side of the

mower drive belt

against the

clutch pulley

. Also, make sure the

mower

drive belt

is not twisted. See illustration “F”.

3. Attach the

front hanger

to the axle support with the

hanger rod

. Fasten with the fasteners as shown. See

illustration “E”.

4. Make sure the

mower drive belt

is between the

clutch

pulley

and the two belt guides. See illustration “F”.

5. Attach the

suspension links

to the

lifter assembly

Fasten with the washers and hair pins. See illustrations
“A” and “B”.

6. Attach the right and the left

adjuster arms

to the

suspension brackets. Fasten with the washers and hair
pins. See illustrations “C” and “D”.

7. Make sure the mower deck is level. See the instructions

on “How To Level The Mower Deck”.

8. Check the operation of the

PTO clutch

. See the

instructions on “How To Adjust The PTO Clutch”.

www.snapper.com

English

Содержание SLT23460 (7800342)

















































Результаты поиска

Содержание SLT23460 (7800342)

Отзывы:

Похожие инструкции для SLT23460 (7800342)

Бренды по названию

Популярные бренды

Snapper SLT23460 (7800342), Инструкции по безопасности и руководство оператора

Результаты поиска

Содержание SLT23460 (7800342)

Отзывы:

Похожие инструкции для SLT23460 (7800342)

Бренды по названию

Популярные бренды