background image

Figure 22: Blade adjustments

A - DISENGAGE Position
B - Blade Rotation Control ENGAGE Position

4. Check the blade(s). Keep a sharp edge on the blade(s).

A blade that is not sharp will cause the tips of the grass
to become brown.

5. Loosen the hardware securing the blade engage cable

bracket (Figure 23) to the mower deck.  Slide the
bracket forward 1/4 - 1/2”.  Tighten the hardware
securely.

Figure 23: Blade engage cable adjustment

A - Blade engage cable bracket

6. Attach the wire to the spark plug. Mow for a short

distance and again check the quality of cut. If
necessary, readjust the blade engage cable bracket.

7. Again check the quality of cut. If the quality of cut has

not improved, replace the 

mower drive belt

. See “How

To Replace The Mower Drive Belt”. If replacing the belt
does not correct the problem, take the unit to an
authorized service center.

8. Move the 

blade rotation control

to the 

DISENGAGE

position

. Stop the engine. Disconnect the wire from the

spark plug. Check the operation of the 

blade brake

.

Rotate the pulleys with your hand. Make sure the 

brake

pads

are pressed tightly against the pulleys (Figure 24).

WARNING: If the brake pads do not press tightly
against the pulleys, take the unit to an authorized
service center.

Figure 24: Blade brake

A - Brake pad against pulley

9. Move the 

blade rotation control

to the 

ENGAGE

position

. Check the pads for the 

blade brake

. If the

pads are excessively worn or damaged, replace the

brake pad

assemblies. Correct replacement parts and

assistance are available from an authorized service
center.

10. Attach the wire to the spark plug. Mow for a short

distance and again check the operation of the 

blade

rotation control

.

11. When you move the 

blade rotation control 

to the

DISENGAGE position

, all movement will stop within five

seconds. If there is movement of the belt or the blades
continue to rotate, engage and disengage the 

blade

rotation control 

five times to remove any excess rubber

from a new 

mower drive belt

. If you need assistance,

take the unit to an authorized service center.

12. If you replace the 

mower drive belt

, be sure to adjust

the blade engage cable bracket.

23

English

A

A

B

A

Содержание SLT23460 (7800342)

















































Отзывы: