Snapper FAST-Vac Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 24

Snapper FAST-Vac Скачать руководство пользователя страница 13

11

Installation

GB

Figure 17. Install Bumper Mount Standoffs
A. Bumper Mount

Collector Installation

A

Figure 18. Install Bagger Mount Plate
A. Bagger Mount Plate
B. Bagger Mount Bracket
C. 5/16-18 X 1-1/4 Bolt
D. 5/16-18 X 3/4 Bolt

A

B

C

D

2. Install the bumper mount (A, Figure 17) onto the

rear bumper. Secure using the existing hardware
on the unit.

3. Install the bagger mount brackets (B, Figure 18)

onto the bagger mount (A) as shown in Figure 18.
Loosely install 5/l6-18 X 3/4" (C) bolts in the
bottom hole of the bagger mount brackets.

4. Install the bagger mount plate to the bumper

mount. Install two (2) 5/16-18 X 1-1/4" bolts (D)
through the top holes of the bagger mount
brackets, and two (2) through the bottom holes on
the bagger mount. Loosely install using four (4)
5/16-18 nylock flange nuts.

5. Tighten the two (2) 5/16-18 X 1-1/4” bolts (D)

installed through the bottom of the bagger mount
plate (A) and bumper mount.

6. Install the muffler deflector (A, Figure 19) onto the

muffler. Make sure that the muffler deflector
directs exhaust off to the side of the mower and
away from the collections bags. Fasten using the
supplied muffler clamp.

IMPORTANT NOTE: Failure to install the muffler
deflector may result in a fire.

Figure 19. Install Muffler Deflector
A. Muffler Deflector

A

«
...
11
12
13
14
15
...
»

Содержание FAST-Vac

























Отзывы:

Нет отзывов