Snapper FAST-Vac Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 24

Snapper FAST-Vac Скачать руководство пользователя страница 12

10

www.snapperpro.com

Installation

Belt Guard Installation

1. Insert two (2) 5/16-18 X 1 bolts (A, Figure 14),

each fitted with one (1) 5/l6 lock washer, up
through the pulley guard holes in the deck.

2. Install the Fast-Vac drive pulley guard onto the

bolts inserted in previous step, secure with two (2)
5/16 nylon nuts. Tighten securely.

3. Install the belt guard (A, Figure 15) between the

pulley guard and the belt guard support clip on the
front part of the blower mount.

4. For convenience, lay the pulley guard cover atop

the belt guard. Secure the belt guard with two (2)
5/16 nylon nuts.

IMPORTANT NOTE: When removing Fast-Vac unit
from mower, install pulley guard cover over opening in
pulley guard to prevent contact with pulley.

Blower Installation

Figure 15. Belt Guard Installation
A. Belt Guard
B. Belt Guard Cover

Figure 14. Pulley Guard Installation
A. 5/16-18 Nylon Nuts

Collector Installation

1. Replace the existing bumper support brackets (A,

Figure 16) with the new bumper support brackets
included with the kit. Use the existing hardware to
secure them into place.

Figure 16. Install Bumper Support Bracket
A. Bumper Support Bracket (RH Side Shown)

A

A

B

A

«
...
10
11
12
13
14
...
»

Содержание FAST-Vac

























Отзывы:

Нет отзывов