background image

 

15 

Section 3 - MAINTENANCE 

 

WARNING 

DO NOT attempt any adjustments, maintenance, 
service or repairs with the engine running. Stop 
engine. Stop blade. Engage parking brake. Remove 
key. Remove spark plug wire from spark plug and 
secure away from plug. Engine and components are 
HOT. Avoid serious burns, allow all parts to cool 
before working on machine. Fuel Filler Cap and Vent 
must be closed securely to prevent fuel spillage. 

 
 
3.4  SERVICE - ANNUALLY  
Perform all maintenance as described in the 
maintenance schedule. 

3.4.1. Engine 
Service engine according to engine owner’s manual. 

 

3.4.2. Air 

Filter 

Refer to engine owner’s manual for service 
instructions. 

 

3.4.3. Oil 

Filter 

Refer to engine owner’s manual for service 
instructions. 
 
 
3.4.4. Engine 

Oil 

Refer to engine owner’s manual for service 
instructions. 

 

3.4.5. Transaxle 
IMPORTANT: DO NOT try to open reservoir cap at 
any time. The transaxle is maintenance free. The 
transaxle does not require any fluid or any service. 
If there is any problem: leakage, or malfunction, 
return the Yard Cruiser immediately to the nearest 
authorized Snapper dealer for service. 

 

3.4.6. Fuel 

Filter 

Service fuel filter as instructed below. Turn key to 
“OFF” position. Engine MUST be stopped and MUST 
be cold before removing filter. Turn fuel shut off valve 
(If equipped) to the “CLOSED” position or perform filter 
change when fuel tank and fuel line are empty. 
1.  Remove hose clamps from fuel filter. 
2.  Remove fuel lines from filter. Discard filter. 
3.  Install new fuel filter. Reinstall hose clamps. See 
Figure 3.10. 

 
 
 
 
 
 
 
 
 
 
 

 

FIGURE 3.10 

 

3.5  STORAGE (OUT OF SEASON) 
If desired, the YARD CRUISER can be stored on the 
rear bumper. Perform the following procedures to insure 
the YARD CRUISER will operate properly when taken 
out of storage. 

1.  Thoroughly clean the YARD CRUISER by 
removing all grass clippings and debris. 
2. 

Perform maintenance and lubrication as 

described in the previous sections. 
3.  Drain fuel from fuel tank. 
4.  Start engine and allow it to run until engine runs 
out of fuel. This allows the carburetor and fuel 
system to remain clean during storage. 
5.  Remove battery. Refer to Section “BATTERY 
REMOVAL AND STORAGE”. 
6.  Close vent on fuel filler cap. Remove key. 
7.  Carefully stand YARD CRUISER on rear bumper 
in desired location for storage. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

NEW FUEL FILTER 
PART NO. 1-4359 

HOSE CLAMPS 

Содержание EYZ15334BVE
































Отзывы: