background image

 

15

Section 4 - REPAIR & ADJUSTMENTS 

 

WARNING 

DO NOT attempt any maintenance, adjustments or 
service with engine and blade running. STOP engine 
and blade. Disconnect spark plug wire and secure 
away from spark plug. Engine and components are 
HOT. Avoid serious burns, allow sufficient time for 
all components to cool. 

 
4.

  Sharpen blade on a grinding wheel at an angle of 

22 to 28 degrees. DO NOT sharpen blade beyond 
original cutting edge. See Figure 4.4. 

 

 

FIGURE 4.4 

 

5. 

Check blade for balance. If necessary, correct 

balance by grinding heavy end of blade. 

6. 

Reinstall blade. See Figure 4.3. Check torque of 

blade retaining cap screw. Recommended torque 
should be 40 ft. lbs.  

 

NOTE: The following sections 4.2 through 
4.4 are for self-propelled models only. 

 

4.2  WHEEL DRIVE CONTROL ADJUSTMENT 

1.

 The wheel drive control is properly adjusted 

when there is 1/16” to 1/8” clearance between the 
inside of the spring hook and the inside of the clutch 
cable eye with the wheel drive control released. See 
Figure 4.5. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

FIGURE 4.5 

 

2. 

To adjust, unhook upper spring from cable eye 

and rotate spring in direction required to extend or 
shorten spring length. 

3. 

Rehook upper spring to cable eye and check 

clearance. Repeat procedure if required. 

 

NOTE:

 The vinyl spring cover should be kept over the 

spring at all times except for adjustments. 
 

4. 

If the wheel drive control fails to return quickly to 

the “OFF” position when released, check for binding 
at the cable holdings located on the side of the right 
handle.  The upper clip should be located 2” below 
the upper knob; the lower clip should be 4” above 
the lower knob. The cable should slide freely with 
the clips installed at these locations.  

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

CLUTCH CABLE 

VINYL SPRING 

1/16” TO 1/8” 
CLEARANCE 

UPPER 
SPRING

LOWER 
SPRING 

CLUTCH CABLE 
EYE

SPRING HOOK 

CABLE 

CLUTCH CABLE EYE

SPRING 

DO NOT SHARPEN 
BEYOND ORIGINAL 
CUTTING EDGE 

22-28º 

BLADE TIP

END VIEW OF 
BLADE ASSEMBLY

ORIGINAL CUTTING EDGE 

Содержание CP215518HV

































Отзывы: