Snapper 5900935, Руководство оператора

Страница: 11 / 60

9
Operator Safety
ROLL BAR INSTRUCTIONS
For models equipped with factory-installed Roll Over
Protection System (ROPS).
OPERATIONAL WARNINGS
• Always use the seat belt when the roll bar is in the
raised position.
• Never use the seat belt when the roll bar is in the
down position.
• Remember there is no roll over protection when
the roll bar is in the down position so it is very
important to always keep the roll bar in the raised
position whenever possible.
• Lower the roll bar to the down position only when
it is absolutely necessary.
• Check for overhead clearances before driving
under any objects. Do not allow roll bar to contact
low overhanging obstacles such as tree branches
and guide wires.
• Never remove the roll bar from the vehicle.
• Do not exceed the machine weight rating of the
roll bar.
• Read and follow all of the instructions shown
below regarding the inspection and maintenance
of the roll bar structure and the seat belt.
INSPECTION OF THE ROLL BAR PROTECTIVE
STRUCTURE
A ROLL BAR, like any other safety device, needs to
be periodically inspected to verify that the integrity of
the device has not been compromised through normal
machine use, misuse, age degradation, modifications,
or a roll over.
WARNING
In order to avoid serious injury or death from
roll over, it is important to follow the warnings
listed below.
WARNING
Failure to properly inspect and maintain the
ROLL BAR protective structure can cause
serious injury or death.
To maintain operator roll over protection and roll bar
effectiveness:
• If a ROLL BAR becomes damaged for any reason,
such as a collision, roll over or impact, the ROLL
BAR must be replaced. Small undetectable
cracks can reduce the effectiveness of the ROLL
BAR. Never weld, straighten, or repair the ROLL
BAR.
• Never alter the ROLL BAR by welding anything to
it or by drilling additional holes.
• BEFORE FIRST TIME USE - Inspect the ROLL
BAR structure and mounting hardware for:
1) Check to make sure the machine GVW (Gross
Vehicle Weight), including attachments,
restrained payload, fuel and operator, is not
in excess of the maximum weight specified on
the ROLL BAR label.
2) Make sure there isn’t any missing, damaged,
or loose mounting hardware.
3) Make sure the ROLL BAR has been correctly
and completely installed.
• EVERY 100 HOURS - Inspect the ROLL BAR
structure and mounting hardware for:
1) Any cracks in the structure (structural members
and/or welds).
2) Significant corrosion on any part of the ROLL
BAR structure or hardware.
3) Missing, damaged, or loose mounting
hardware
4) Mounting hardware that is of a grade lesser
than specified.
5) Machine GVW (Gross Vehicle Weight),
including attachments, restrained payload,
fuel and operator, in excess of the maximum
weight specified on the ROLL BAR label.
6) Any modifications that have been made, such
as unauthorized welds and holes.
7) Any permanent deformation or twisting of the
ROLL BAR structure.
8) That the ROLL BAR label is still in place and is
readable.
9) That the ROLL BAR on-product warning labels
are still on the ROLL BAR and are readable.
• If there is any doubt as to the condition of the
ROLL BAR, remove the machine from service and
contact your dealer for assistance.
leaks. Make sure all hydraulic fluid connections
are tight and all hydraulic hoses and lines are in
good condition before applying pressure to the
system. If leaks occur, have the unit serviced
immediately by your authorized dealer.
26. WARNING: Stored energy device. Improper
release of springs can result in serious personal
injury. Springs should be removed by an
authorized technician.
27. Models equipped with an engine radiator:
WARNING: Stored energy device. To prevent
serious bodily injury from hot coolant or steam
blow-out, never attempt to remove the radiator
cap while the engine is running. Stop the engine
and wait until it is cool. Even then, use extreme
care when removing the cap.
Not
for
Reproduction