Operating Instructions
29
●
The LP Gas Cylinder must be a 20 pound cylinder and have a Type 1 Cylinder Valve Outlet
Connector.
●
Handle the Cylinder with care - do not drop it.
●
When you are not using the grill, the LP Gas Cylinder should be dis-
connected.
●
Connect the regulator and hand tighten firmly.
●
Do a leak test each time you connect a LP Gas Cylinder and before
lighting the grill.
●
Never use a match or lit flame to test for leaks.
●
To test, prepare a weak solution of detergent and water. Spray or
swab the solution onto the connection of the regulator to the LP Gas
Cylinder valve, and on all the joints in the hose connections up to the burner valves (which
MUST be closed in the "OFF" position).
●
Open the LP Gas Cylinder valve, and watch for any bubbles to appear at all the connection
points. No bubbles indicate - All Clear!
●
If there are any bubbles, there is a leak which must be fixed.
●
Never obstruct the flow of combustion and ventilation air.
Connecting the LP gas cylinder to the grill
Lighting the grill
●
Always open the Lid before lighting the grill.
●
All burner knobs should be in the "OFF" position.
●
Open the LP Gas Cylinder valve,1 – 1 1/2 turns.
●
Select one burner to light. Push and turn control knob to “LIGHT”
Position.
●
Press the electronic igniter button and hold for 5 seconds to light burner.
●
You can then adjust the knob to your desired setting.
●
If the burner did not light, turn the knob back to the “OFF” position, wait 5 minutes for any gas
to clear away, and then repeat the lighting procedure.
●
Follow same steps to light the other burners.
●
After using the grill, - turn all burner knobs to the "LIGHT" position and then push fully in and
turn to the "OFF" position.
●
At once turn the valve on the LP Gas Cylinder OFF.
●
IF the igniter does NOT light the burner, you can light it
with a match or a piece of burning paper - hold the
match or paper with the Match Holder ( attached at the side
of the grill) , put it through the openings in the Cooking Grid
and next to the Flame Tent covering the burner. Then fol-
low the lighting procedure above.
●
Observe the proper burner flame - it should be a blue/
yellow color about 1/2” long.
OPERATING INSTRUCTIONS
YELLOW
BLUE
Burner
Good Flame
Bad Flame
1. Read instructions before lighting.
2. Open Lid during lighting.
3. Make sure all control knobs are OFF.
4. Turn on gas supply.
5. (2-Burner Models) Push in and turn the left control knob counterclockwise to “LIGHT” position. This
burner must be lit first before other burner can be lit.
(3-Burner Models) Push in and turn the middle control knob counterclockwise to “LIGHT” position.
This burner must be lit first before other burners can be lit.
(4-Burner Models) Push in and turn either of the middle control knobs counterclockwise to “LIGHT”
position. The two middle burners must be lit first before other burners can be lit.
6. Press the ignitor button rapidly several times until the burner is lit.
If the ignitor does not light the burner, you can light it with a match or a piece of burning paper. Hold the match or paper
with the Match Holder (attached to the side of the grill), put it through opening in Cooking Grid and next to the Flame Tent
covering the burner. Then follow the lighting procedure above.
7. For cooking with more burners, push in and turn the control knob
counterclockwise until the burner is lit.
WARNING: If ignition does not occur in 5 seconds, immediately turn the
burner controls OFF, wait 5 minutes and repeat the lighting process.
WARNING: Turn the gas supply off when not in use.
After using the grill, turn all burner knobs to the “LIGHT” position
and then push fully in and turn to the “OFF” position. Turn OFF
the valve on the LP Gas Cylinder.
29
●
The LP Gas Cylinder must be a 20 pound cylinder and have a Type 1 Cylinder Valve Outlet
Connector.
●
Handle the Cylinder with care - do not drop it.
●
When you are not using the grill, the LP Gas Cylinder should be dis-
connected.
●
Connect the regulator and hand tighten firmly.
●
Do a leak test each time you connect a LP Gas Cylinder and before
lighting the grill.
●
Never use a match or lit flame to test for leaks.
●
To test, prepare a weak solution of detergent and water. Spray or
swab the solution onto the connection of the regulator to the LP Gas
Cylinder valve, and on all the joints in the hose connections up to the burner valves (which
MUST be closed in the "OFF" position).
●
Open the LP Gas Cylinder valve, and watch for any bubbles to appear at all the connection
points. No bubbles indicate - All Clear!
●
If there are any bubbles, there is a leak which must be fixed.
●
Never obstruct the flow of combustion and ventilation air.
Connecting the LP gas cylinder to the grill
Lighting the grill
●
Always open the Lid before lighting the grill.
●
All burner knobs should be in the "OFF" position.
●
Open the LP Gas Cylinder valve,1 – 1 1/2 turns.
●
Select one burner to light. Push and turn control knob to “LIGHT”
Position.
●
Press the electronic igniter button and hold for 5 seconds to light burner.
●
You can then adjust the knob to your desired setting.
●
If the burner did not light, turn the knob back to the “OFF” position, wait 5 minutes for any gas
to clear away, and then repeat the lighting procedure.
●
Follow same steps to light the other burners.
●
After using the grill, - turn all burner knobs to the "LIGHT" position and then push fully in and
turn to the "OFF" position.
●
At once turn the valve on the LP Gas Cylinder OFF.
●
IF the igniter does NOT light the burner, you can light it
with a match or a piece of burning paper - hold the
match or paper with the Match Holder ( attached at the side
of the grill) , put it through the openings in the Cooking Grid
and next to the Flame Tent covering the burner. Then fol-
low the lighting procedure above.
●
Observe the proper burner flame - it should be a blue/
yellow color about 1/2” long.
OPERATING INSTRUCTIONS
YELLOW
BLUE
Burner
Good Flame
Bad Flame
Good
Flame
Bad
Flame
Yellow
Blue
Burner
Observe the proper burner
flame. It should be a blue/yellow
color about 1/2” long.
19
