manualshive.com logo in svg

smith&nephew ZUK, Хирургические техники

Поделиться
Скачать
smith&nephew ZUK Скачать руководство пользователя страница 7

5

Exposure

The incision can be made with the leg 
in flexion or extension, according to 
preference. Make a medial parapatellar 
skin incision extending from the 
superior pole of the patella to about 
2cm-4cm below the joint line adjacent 
to the tibial tubercle (Fig. 4).

Incise the joint capsule in line with 
the skin incision beginning just distal 
to the vastus medialis muscle and 
extending to a point distal to the tibial 
plateau (Fig. 5). Excise the fat pad, as 
necessary to facilitate visualization, 
being careful not to cut the anterior 
horn of the lateral meniscus. Reflect 
the soft tissue subperiosteally from  
the tibia along the joint line back 
towards, but not into, the collateral  
ligament. Excise the anterior third  
of the meniscus. The remainder of  
the meniscus will be removed after 
bone resection.

A subperiosteal dissection should be 
carried out towards the midline, ending 
at the patellar tendon insertion. This 
will facilitate positioning of the tibial 
cutting guide.

Debride the joint and inspect it 
carefully. Remove intercondylar 
osteophytes to avoid impingement with 
the tibial spine or cruciate ligament. 
Also, remove peripheral osteophytes 
that interfere with the collateral 
ligaments and capsule. With medial 
compartment disease, osteophytes 
are commonly found on the lateral 
aspect of the medial tibial eminence 
and anterior to the origin of the ACL. 
Final debridement will be performed 
before component implantation. Careful 
osteophyte removal may be important 
in achieving full extension.

Fig. 4

7 – 12cm  

Skin Incision

Fig. 5

Capsular 

Incision

T-Incision

Vastus 

Medialis

Vastus 

Laderalis

Patient Preparation

With the patient in the supine position, 
test the range of hip and knee flexion.  
If unable to achieve 120° of knee 
flexion, a larger incision may be 
necessary to create sufficient exposure. 
Wrap the ankle area with an elastic 
wrap. Do not place bulky drapes on 
the distal tibia, ankle, or foot. A bulky 
drape in this area will make it difficult 
to locate the center of the ankle, 
and will displace the Tibial Resector, 
which may cause inaccurate cuts.

Be sure that the proximal femur 
is accessible for assessing the 
femoral head location. Use anatomic 
landmarks to identify the location of 
the femoral head. Alternatively, the 
surgeon may prefer to reference the 
anterior-superior iliac spine.

Technique tip: Place a marker, such 
as an EKG electrode, over the center 
of the femoral head. Then confirm the 
location with an A/P radiograph.

Содержание ZUK

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды