manualshive.com logo in svg

smith&nephew ZUK, Хирургические техники

Поделиться
Скачать
smith&nephew ZUK Скачать руководство пользователя страница 36

34

Step Five

Check Flexion/Extension Gaps

To assess the flexion and extension 
gaps, different Flexion/Extension  
Gap Spacers are available that 
correspond to the 8mm, 10mm, 12mm, 
and 14mm tibial articular surface 
thicknesses. The thick end of each 
spacer duplicates the combined 
thickness of the corresponding tibial 
and femoral components in extension.  
The thin end of each spacer simulates 
the thickness of the tibial component 
in flexion.

Check the extension gap by inserting 
the thick end of the 8mm Flexion/
Extension Gap Spacer into the  
joint (Fig.18).

Remove the Flexion/Extension Gap 
Spacer and flex the knee. Check the 
flexion gap by inserting the thin end 
of the selected Flexion/Extension Gap 
Spacer into the joint (Fig. 19). If, in both 
flexion and extension, the joint space 
is too tight to insert the 8mm Flexion/
Extension Gap Spacer, then more tibial 
bone must be removed. Then use 
the Flexion/Extension Gap Spacers to 
recheck the gaps.

Fig. 18

Fig. 19

If in both flexion and extension the joint 
space is too loose, insert progressively 
thicker Flexion/Extension Gap Spacers 
and repeat the gap checking.

If tight in extension and acceptable in 
flexion, two options may be pursued:

1.  Recut proximal tibia with less  

tibial slope

2. Recut 1mm – 2mm of distal femur

After any adjustment of the flexion 
and/or extension gap is made, use  
the Flexion/Extension Gap Spacers  
to recheck the gaps. 

Verifying the  

gaps at this stage of the procedure 
will reduce the likelihood of a gap 
imbalance during the trial reduction.

Содержание ZUK

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды