background image

SPS8

Limited Equipment Warranty

All statements, technical information and recommendations contained in SMITH’s literature are based on tests believed to be reliable, but the accuracy 

or completeness thereof is not guaranteed and the following is made in lieu of all warranties, expressed or implied. SMITH warrants all equipment or part 

referenced in this document which is manufactured by SMITH and bearing its name to be free from defects in material and workmanship on the date of 

sale to the original purchaser under normal use and maintenance as herein provided. This warranty does not apply to components manufactured by others 

such as, but not limited to, bearings and engines; such components that may or may not have their own warranties.  

With  the  exception  of  any  special,  extended,  or  limited  warranty  published  by  SMITH,  SMITH  will,  for  a  period  of  three  months  (90  days)  from  the 

date of sale or up to five hundred (500) hours of use by buyer, whichever shall occur first; repair or replace any part of the equipment determined by 

SMITH to be defective. This warranty applies only when the equipment or part is installed, operated and maintained in accordance with SMITH’s written 

recommendations.

SMITH’s sole obligation for any breach of warranty or breach of contract for defects, deliberate or accidental omissions, shall be limited to repairing, 

replacing  or  allowing  credit  for,  at  SMITH’s  option,  any  part  which,  under  normal  and  proper  use  and  maintenance,  proves  defective  in  material  or 

workmanship within warranty period, provided, however, that notice of any such defect or omission and satisfactory proof thereof is promptly given by 

buyer to SMITH, and thereafter, such defective part is returned to SMITH with transportation charges prepaid, and SMITH’s examination proves such part 

to have been defective. This warranty does not obligate SMITH to bear any transportation charges or personnel time in connection with the replacement 

or repair of defective parts. This warranty does not obligate SMITH to bear any expense for travel time or of personnel in connection with any service calls. 

SMITH will not, in any event, be liable to the user for any consequential damages arising out of this sale for the loss of use, lost profits or revenue, interest, 

lost goodwill or work stoppage. SMITH shall not be liable for any injury, loss or damage, direct or consequential, arising out of the use or the inability to use 

the product or for environmental claims. It being understood that SMITH has no means of controlling the products final use; therefore, it shall be buyer’s 

responsibility to determine suitability of product for intended use and buyer assumes all risks and liabilities whatsoever, in connection therewith. In no event 

shall SMITH be liable for consequential or special damages. Used products are sold on an “as is” basis, and there is no implied warranty of merchantability 

or of fitness for a particular purpose, unless made in writing by an officer at SMITH’s office.

This warranty does not cover, and SMITH shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, 

misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-SMITH component parts. 

Nor shall SMITH be liable for malfunction, damage or wear caused by the incompatibility of SMITH equipment with structures, accessories, equipment 

or materials not supplied by SMITH, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment 

or materials not supplied by SMITH. This warranty does not apply in respect to damages to any product or accessory or attachment thereof caused by 

overloading or other misuse, neglect or accident, nor does this warranty apply to any product or accessory or attachment thereof, which has been repaired 

or altered in any way which, in the sole judgment of SMITH, affects the performance, stability or general purpose for which it was manufactured. In the 

manufacture of buyer’s equipment, parts may be omitted or equivalent functioning equipment and components may be substituted for the original specified 

equipment upon the sole judgment and discretion of SMITH.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized SMITH Reseller for verification of the 

claimed defect. If the claimed defect is verified, SMITH will repair or replace free of charge any defective parts and return of merchandise back to the 

customer freight collect. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable 

charge, which charges may include the costs of parts, labor and transportation.

THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO 

WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.

SMITH’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy (including, 

but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) 

shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.

SMITH  MAKES  NO  WARRANTY,  AND  DISCLAIMS  ALL  IMPLIED  WARRANTIES  OF  MERCHANTABILITY  AND  FITNESS  FOR  A  PARTICULAR 

PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT MANUFACTURED BY SMITH.

These items sold, but not manufactured by SMITH (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. 

SMITH will provide purchaser with reasonable assistance in making any claim for breach of these warranties. In no event will SMITH be liable for indirect, 

incidental, special or consequential damages resulting from SMITH supplying equipment hereunder, or the furnishing, performance, or use of any products 

or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of SMITH, or otherwise.

ADDITIONAL WARRANTY COVERAGE - SMITH does provide extended warranty and wear warranty for products.

Corrections - typographical or clerical errors contained herein are subject to correction by SMITH.

Assignment - buyer shall not assign or transfer this warranty without SMITH’s written consent.

Entire agreement and applicable law - the rights and obligations of SMITH and buyer shall be governed by the laws of the state of Florida, U.S.A. In force 

on date hereof. The provisions hereof are intended by buyer and SMITH as a final expression of their agreement, and are intended also, as a complete 

and exclusive statement of all terms apply cable to buyer’s order. No waiver, modification, or addition to any of the terms hereof shall be binding on SMITH, 

unless made in writing by an officer at SMITH’s office as stated herein. In the event of conflict between buyer’s purchase order and the terms hereof, the 

latter shall control. If any provisions herein are to any extent invalid or unenforceable, the remainder of the warranty shall not be effected thereby and shall 

be valid and enforceable to the fullest extent permitted by law.

Legal action - buyer shall be responsible for all costs of collection of outstanding indebtedness, including but not limited to attorney’s fees and court costs 

to seller.  Buyer shall reimburse seller for any and all litigation expenses seller incurs as a result of an unsuccessful buyer claim. The jurisdiction and venue 

of the court for any litigation, state or federal, brought by the buyer and/or seller shall be located in venue determined by seller.

Fair labor standards - seller’s products are produced in the United States and in conformity with all applicable provisions of the fair labor standards act of 

1938 as amended and any regulations and orders of the United States Department of Labor issued thereunder.

All written and visual data contained in this document reflects the most current product information available at the time of this publication. SMITH reserves 

the right to make changes at any time without notice.

TO ORDER, contact your SMITH distributor or call 1-800-653-9311 to identify the nearest distributor. 

SMITH Manufacturing Co, Inc. 

1610 South Dixie Highway

Pompano Beach, FL 33060

www.smithmfg.com

SMITH Manufacturing     1-800-653-9311     www.SmithMfg.com

31

Содержание SPS8


































Отзывы: