background image

GT INSTALLATION AND OPERATION INSTRUCTIONS

Page 3

WARNING: At elevations greater than 2000 ft, 

660 m

, the combustion of the GT must be checked 

with a calibrated combustion analyzer to ensure 
safe and reliable operation. Consult the Operating 
Instructions Section for instructions on adjusting 
the input to provide proper operation. Failure to 
comply with this warning can result in excessive 
levels of carbon monoxide causing severe 
personal injury or death! 

BOILER LOCATION

WARNING: The clearances to combustible 
construction listed in Table 1 must be maintained. 
Failure to comply with this warning can result in 
a extensive property damage, severe personal 
injury or death!

CAUTION: This boiler is designed to operate only 
in residential and commercial heating systems. It is 
not intended for:
1.  Outdoor installations, or unheated spaces, which 

can cause freezing.

2.  Process heating of potable water, or any other 

fl uids.

3. Un-pressurized, and gravity feed heating 

systems.

4.  Heating systems with very low pressures or 

fl ow.

Improper use or installation will seriously damage 
the boiler, voiding warranty!

1.   Locate the boiler in an area that provides good 

access to the unit. Keep in mind that servicing may 
require the removal of jacket panels. Accessibility 
clearances should take precedence over fire 
protection clearances. Table 1 lists the minimum 
clearances for servicing, however 

24 in

610 mm

 is 

recommended.

2.   An optimum site will be level, central to the hot water 

piping system and close to an outside wall.

NOTE: This boiler is designed for direct placement 
on a combustible fl oor. Never install this boiler on 
carpeting!

3.   DO NOT install this boiler in a location that would 

subject any of the gas ignition components to direct 
contact with water or excessive moisture during 
operation or servicing. 

The boiler location ambient 

temperature must be no less than 50°F, 

10°C

 

including the condensate line

.

4.   NEVER store objects on or around the boiler.

5.   This boiler may be wall mounted. See the Wall Hung 

Conversion section listed in the table of contents.

WARNING: Never store combustible materials, 
gasoline or any product containing fl ammable 
vapors or liquids in the vicinity of the boiler.  
Failure to comply with this warning can result 
in extensive property damage, severe personal 
injury or death!

WARNING: Liquefied Petroleum, LP, gas is 
heavier than air; it is imperative that your boiler 
is not installed in a pit or similar location that 
will permit heavier than air gas to collect. Local 
Codes may require appliances fueled with LP 
gas be provided with an approved means, of 
removing unburned gases from the room. Check 
your local codes for this requirement. Failure to 
comply with this warning can result in extensive 
property damage, severe personal injury or 
death!

Figure 1- Input vs Elevation Graph

100

110

120

130

140

150

160

170

180

190

200

0-2000

3000

4000

5000

6000

7000

8000

9000

10000

Elevation (ft)

)h

b

M( t

up

nI

GT-150

GT-200

Содержание GT-150









































Отзывы: