Smeg UD515D Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 39

Smeg UD515D Скачать руководство пользователя страница 37

37

13

TROUBLESHOOTING

In  case  the  pump  is  not  working  properly,  follow  the  steps
below:
Empty the dishwasher out using a container and disconnect
the power.
Remove screw A, release tab B and lift it upwards.
Make sure that the covered drain  pump impeller can rotate
freely, and that there are no dirt residues, limestone, or pieces
of glass. Do not use tools, screwdrivers, scissors, etc.

PROBLEM

POSSIBLE CAUSE

POSSIBLE SOLUTION

THE INDICATOR LIGHT L1
DOES NOT LIGHT UP

line voltage failure

Verify electricity connection.

THE WASHING PROGRAM
DOES NOT START

The dishwasher filling is not
over yet.

Wait for FILL to disappear off the
display

CLOSE stays on display

If CLOSE stays even with the hood
closed, contact the After-Sales
Service.

POOR WASHING RESULTS

Clogged or crusted spray
arms holes.

Dismount and clean the spray arms
(10.2 Periodical checks)

Clogged filter

Read “cleaning the filters during the
day”

Insufficient or improper
detergent or rinse aid.

Verify detergent type and quantity.

Failing or insufficient use of
detergent or rinse aid: the
detergent or rinse aid cannot
be withdrawn from the
dedicated containers.

Worn or broken internal tube for
detergent or rinse aid of the
peristaltic pump, to be replaced by
the After-Sales Service.
This ordinary maintenance service is
recommended at least once a year
for the correct functioning of the
dosers.

Badly positioned dishes /
glasses.

Place dishes / glasses correctly.

Low washing temperature

Verify the temperature displayed, if it
is inferior than 50°C contact
customer Support.

A

B

«
...
35
36
37
38
39
»

Содержание UD515D








































Отзывы:

Нет отзывов