background image

 

           ProtoNode Start-Up Guide 

Page 37 of 37 

Appendix E. Limited 2 Year Warranty 

Sierra  Monitor  Corporation  warrants  its  products  to  be  free  from  defects  in  workmanship  or 
material  under  normal  use  and  service  for  two  years  after  date  of  shipment.  Sierra  Monitor 
Corporation  will  repair  or  replace  any  equipment  found  to  be  defective  during  the  warranty 
period.

 

Final determination of the nature and responsibility for defective or damaged equipment 

will be made by Sierra Monitor Corporation personnel. 

All warranties hereunder are contingent upon proper use in the application for which the product 
was  intended  and  do  not  cover  products  which  have  been  modified  or  repaired  without  Sierra 
Monitor  Corporation’s  approval  or  which  have  been  subjected  to  accident,  improper 
maintenance,  installation  or  application,  or  on  which  original  identification  marks  have  been 
removed or altered.

 

This Limited Warranty also will not apply to interconnecting cables or wires, 

consumables or to any damage resulting from battery leakage. 

In all cases Sierra Monitor Corporation’s responsibility and liability under this warranty shall be 
limited  to  the  cost  of  the  equipment.  The  purchaser  must  obtain  shipping  instructions  for  the 
prepaid  return  of  any  item  under  this  warranty  provision  and  compliance  with  such  instruction 
shall be a condition of this warranty. 

Except  for  the  express  warranty  stated  above,  Sierra  Monitor  Corporation  disclaims  all 
warranties  with  regard  to  the  products  sold  hereunder  including  all  implied  warranties  of 
merchantability and fitness and the express warranties stated herein are in lieu of all obligations 
or liabilities on the part of Sierra Monitor Corporation for damages including, but not limited to, 
consequential  damages  arising  out  of/or  in  connection  with  the  use  or  performance  of  the 
product. 

 

 

 

 

 

 

 

 

 

Содержание FPC-N36






































Отзывы: