Element Part No.
Applicable
tubing O.D
Applicable tubing ø3.2
Applicable tubing ø4
Applicable tubing ø6
Applicable tubing ø8
VVQ1000-50A-C3
VVQ1000-50A-C4
VVQ1000-50A-C6
VVQ1000-51A-C4
VVQ1000-51A-C6
VVQ1000-51A-C8
VQ2000
VQ1000
Fitting assembly part no.
Purchasing order is available in units of 10 pieces.
Caution
Attaching and detaching connectors
Type
Element part no.
VQ1000
VQ2000
VQ0000
VVQ0000-82A-4
VVQ1000-82A-4
VVQ2000-82A-4
Built-in silencer,
direct exhaust
(-S)
∗
The minimum order quantity is 10 pcs.
For obtaining the flow rate, refer to pages 2-1-8 to 2-1-11.
How to Remove
<Procedure>
Mounting
To detach a connector, remove the pawl from
the groove by pushing the lever downward with
your thumb, and pull the connector straight out.
The cylinder port fittings are a
cassette for easy replacement.
(Except VQ1000)
The fittings are blocked by a clip
inserted from the top of the
valve. Remove the clip with a
screwdriver to remove fittings.
For replacement, insert the
fitting assembly until it strikes
against the inside wall and then
re-insert the clip to the specified
position.
1.
Protect O-rings from scratches and dust to prevent air leakage.
2.
The tightening torque for inserting fittings to the M5 thread
assembly should be 0.8 to 1.4 N·m
1.
Loosen the clamp screw
on side (a) of the end
plate on both sides.
2.
Lift side (a) of the
manifold base and slide
the end plate in the
direction of (2) shown in
the figure to remove.
1.
Hook side (b) of the
manifold base on the
DIN rail.
2.
Press down side (a) and
mount the end plate on
the DIN rail. Tighten the
clamp screw on side (a)
of the end plate.
The proper tightening
torque for screws is 0.4
to 0.6 N·m.
A silencer element is incorporated in the end plate on both sides of
the manifold base. A dirty and choked element may reduce cylinder
speed or cause malfunction. Clean or replace the dirty element.
Remove the cover from the side of the end plate and
remove the old element with a screwdriver, etc.
To attach a connector, hold
the lever and connector unit
between your fingers and
insert straight onto the pins of
the solenoid valve so that the
lever’s pawl is pushed into the
groove and locks.
Crimping the lead wire and
socket
Peel 3.2 to 3.7 mm of the tip
of lead wire, enter the core
wires and press contact it by
a press tool. Be careful so
that the cover of lead wire
does not enter into the core
press contacting part.
Attaching and detaching lead wires with sockets
Attaching
Insert a socket in the square hole (Indicated as +, –) of
connector, push in the lead wire and lock by hanging the hook of
socket to the seat of connector. (Pushing-in can open the hook
and lock it automatically.) Then confirm the lock by lightly pulling
on the lead wire.
Detaching
To detach a socket from a connector, pull out the lead wire while
pressing the socket’s hook with a stick having a thin tip (approx. 1
mm). If the socket will
be used again, first
spread the hook
outward.
—
—
Cover
Cover
Pin
Pin
Concave
Concave
Connector
Connector
Lever
DC indicator
Socket
Part no.
DXT170-71-1
Lead wire 0.2 to 0.33 mm
2
(Max. cover diameter ø1.7 mm)
Hook
Hook
Terminal
Core wire
crimping
area
Crimping area
Core wire
Lead wire
Lead wire
0.2 to 0.33 mm
2
(Max. cover diameter ø1.7 mm)
Socket
Cover
Fitting
assembly
Clip
(a)
(a)
(b)
(b)
(1)
(1)
(2)
(2)
Replacement of Cylinder Port Fittings
Caution
Built-in Silencer Replacement Element
How to Use Plug Connector
Mounting/Removing from the DIN Rail
How to Calculate the Flow Rate
Hook
Caution
Caution
Caution
2-4-67
Series
VQ0000/1000/2000
Plug Lead Unit: Flip Type
Body Ported
VQC
SQ
VQ0
VQ4
VQ5
VQZ
VQD