background image

 

Gardner Denver Driver Manual 

Page 4 of 13 

 GARDNER DENVER AUTO SENTRY ES/RS2000 DES CRIPTION  

The Gardner Denver Auto Sentry ES/RS2000 driver allows the FieldServer to transfer  data from devices 
over  either  RS-232  or  RS-485  using  Gardner  Denver  Auto  Sentry  ES/RS2000  protocol.    The  driver  can 
be  configured  to  communicate  with  ES  Controllers  with  software  versions  V2.0X,  V2.1X  and  RS2000 
Controllers with software versions V4.0X  

The client driver implements the following functionality: 

 

Polls controllers for service and maintenance data. 

 

Polls controllers for operating mode data. 

 

Polls controllers for operating data. 

The driver can poll up to 8 units connected to one ES/RS2000 Controller. It always sets the active unit on 
the ES/RS2000 Controller  before polling for data even if consecutive  polls are for the same unit. This is 
done to prevent synchronization problems. 

Gardner  Denver  ES/RS2000  Controllers  implements  three  message  types  for  which  the  driver  can  poll. 
The driver does not validate the message data fields for correct values although it does validate data field 
lengths, for example, shutdown codes reported by V2.1 ES Controllers range from 0 to 27. If a code of 28 
is  reported,  the  driver  will  not  flag  it  as  an  error  since  codes  have  to  be  interpreted  by  the  operator. 
However, a message length longer than 2 digits will be reported as an error. 

Max Nodes Supported 

FieldServer Mode 

Nodes  Comments 

Client 

A  client  node  can  communicate  with  up  to  8  units  connected  to  a 
ES/RS2000 Controller 

DRIVER SCOPE OF SUPPLY 

2.1 

Supplied by Sierra Monitor Corporation  

Part # 

Description 

FS-8915-10  UTP cable (7 foot) for RS-232 use 
FS-8917-03  RJ45 to DB9M connector adapter 

 

2.2 

Provided by the Supplier of 3

r d

 Party Equipment 

2.2.1  Required 3

r d

 Part y Hardware  

Part #  Description 

ES/RS2000 controller 

 

2.2.2  Required 3

r d

 Part y Configuration  

The  ES/RS2000  Controller  must  be  set  up  in  the  correct  mode  to  support  either  RS-232  or  RS-485 
communications to an externa

l monitoring system. Please refer to manufacturer’s setup instructions. 

2.2.3  Optional Item s 

Part # 

Vendor/Manufacturer  Description 

485LDRC  B&B Electronics 

RS-232/RS-485 converter 

 

Содержание FieldServer FS-8700-60 Gardner Denver














Отзывы: