Smarthome X10WS467 Скачать руководство пользователя страница 7

                                                                                                                                  Page 7 of 7                                                                       X10WS467 Rev: 10/7/2011 6:14 PM 

Troubleshooting 

Problem Possible 

Cause 

Solution 

Make sure the circuit breaker is turned on. 
Make sure the air gap (Set button) is not pulled out. 

X10 Toggle Wall Switch 
is not controlling the 
load.  

X10 Toggle Wall Switch 
may not be getting power.  

Check the junction box wires to ensure all 
connections are tight and no bare wires are exposed. 

X10 Toggle Wall Switch 
and the controller may be 
on opposite phases.  

Install an X10 signal bridge or coupler to bridge the 
power line phases.  

Move the other modules to different areas of your 
home to reduce noise on the power line. 

X10 Toggle Wall Switch 
is not receiving signals 
from X10 controllers. 

Other modules may be 
loading down the signal or 
creating too much noise.  

Install a noise filter between the X10 Toggle Wall 
Switch and the noise-producing device.  

X10 Toggle Wall Switch 
turned on by itself.  

Stray X10 signals from a 
neighboring system may 
have triggered X10 Toggle 
Wall Switch.  

Install a power line signal blocker in your home to 
keep X10 signals from other systems from interfering. 

Pull the Set button all the way out to air-gap it, and 
then push it back in until it is flush with the wallplate.  

X10 Toggle Wall Switch 
is locked up.  

A surge or excessive noise 
on the power line may have 
glitched it.  

If the above doesn’t work, perform a factory reset.  

If you have tried these solutions, reviewed this Owner’s Manual, and still cannot resolve an issue you are 
having with X10 Toggle Wall Switch, please call: 800-762-7845.  

Certification and Warranty 

Certification 

This product has been thoroughly tested by ITS ETL SEMKO, a nationally recognized independent third-party testing laboratory. The North American 
ETL Listed mark signifies that the device has been tested to and has met the requirements of a widely recognized consensus of U.S. and Canadian 
device safety standards, that the manufacturing site has been audited, and that the manufacturer has agreed to a program of quarterly factory follow-
up inspections to verify continued conformance.  

Limited Warranty 

Seller warrants to the original consumer purchaser of this product that, for a period of 90 days from the date of purchase, this product will be free from 
defects in material and workmanship and will perform in substantial conformity to the description of the product in this Owner’s Manual. This warranty 
shall not apply to defects or errors caused by misuse or neglect. If the product is found to be defective in material or workmanship, or if the product 
does not perform as warranted above during the warranty period, Seller will either repair it, replace it, or refund the purchase price, at its option, upon 
receipt of the product at the address below, postage prepaid, with proof of the date of purchase and an explanation of the defect or error. The repair, 
replacement, or refund that is provided for above shall be the full extent of Seller’s liability with respect to this product. For repair or replacement during 
the warranty period, call the Tech Support at 800-762-7845 with the Model # and Revision # of the device to receive an RMA# and send the product, 
along with all other required materials to:  

 
Smarthome 
ATTN: Receiving 
16542 Millikan Ave. 
Irvine, CA 92606-5027 

Limitations 

The above warranty is in lieu of and Seller disclaims all other warranties, whether oral or written, express or implied, including any warranty or 
merchantability or fitness for a particular purpose. Any implied warranty, including any warranty of merchantability or fitness for a particular purpose, 
which may not be disclaimed or supplanted as provided above shall be limited to the 90-day of the express warranty above. No other representation or 
claim of any nature by any person shall be binding upon Seller or modify the terms of the above warranty and disclaimer.  
Home automation devices have the risk of failure to operate, incorrect operation, or electrical or mechanical tampering. For optimal use, manually verify 
the device state. Any home automation device should be viewed as a convenience, but not as a sole method for controlling your home.  

In no event shall Seller be liable for special, incidental, consequential, or other damages resulting from possession or use of this device, including 
without limitation damage to property and, to the extent permitted by law, personal injury, even if Seller knew or should have known of the possibility of 
such damages. Some states do not allow limitations on how long an implied warranty lasts and/or the exclusion or limitation of damages, in which case 
the above limitations and/or exclusions may not apply to you. You may also have other legal rights that may vary from state to state.  

© Copyright 2011 Smarthome, 16542 Millikan Ave., Irvine, CA 92606, 800-762-7845, 

www.smarthome.com

 

 

Содержание X10WS467








Отзывы: