background image

HGM9560 BUS TIE MAINS PARALLEL UNIT 

HGM9560 Bus Tie Mains Parallel Unit        ISSUE 2013-12-30          Version 1.0        Page 17 of 51 

4.5 MANUAL START/STOP OPERATION 

Manual mode is selected by pressing the 

  button; a LED besides the button will illuminate 

to confirm the operation. 

Manual Start Operation: 

1.  Press 

  button  to  start  the  genset

,  the  controller  will  issue  a  start  command,    “Start 

Request XX

s” information will be displayed on LCD;   

2.  Any  available  9560  in  auto  mode  will  be  issued  with  a  start  signal.  Please  refer  to  the  9510 

operating manual for further details of the start sequence. 

3.  Once the Minimum number of sets have synchronized onto the bus, the 9560 will enter into 

normal running: 

4.  If  the  number  of  the  synchronized  set  is  less  than  the  Minimum  number 

after  the  “Start 

Request” delay is over, then the “Too Few Modules” alarm will be initiated. 

Manual Transfer Procedures 

Bus Close Operation

: During genset is normal running, press Bus Close Button 

 

1) 

If mains switch didn’t close, then bus close relay activate.   

2)  If mains switch already closed, the controller will adjust speed and voltage to synchronize bus 

with  mains;  when  synchronism  requirements  has  been  achieved,  bus  close  signal  will  be 

initiated and the bus will be paralleled with the mains. Once the bus has synchronized to the 

mains, the power will be ramped off the mains. 

Bus Open Operation

Press Bus Open Button 

1) 

If mains switch didn’t close, then bus open relay activate.   

2)  If mains switch already closed, first of all, the controller will transfer load to mains, and only 

then bus open relay activate. 

Mains Close Operation

: During mains is in normal status, press Mains Close Button 

 

1)  If bus 

switch didn’t close, then mains close relay activate.   

2)  If bus switch already closed, the controller will adjust speed and voltage to synchronize bus 

with mains; when synchronism requirements has been achieved, mains close signal will be 

initiated and the mains will be paralleled with the bus. Once the mains has synchronised to 

the bus, the power will be ramped off the bus. 

 

 

Содержание HGM9560




















































Отзывы: