background image

Longo programmable controller LPC-2.DT1B

Actual temp.: 

Actual room temperature 0 .. 5000 represents  0.00 .. 50.00 °C.

Actual light: 

Actual room light intensity 0 .. 100 represents 0 .. 100%. 

Light x (Off/On) command: 

remote On/Off command for individual light. This command is enabled

using corresponding Light x (Local/Remote) command.

Light x (Local/Remote) command: 

Enables corresponding light On/Off remote command.

Clock display enable command:

 Time Clock display enable command from MCU. When active, time

will be displayed on CP.

Light   Off   MIN   set   value:

 

Below   this   set   value,   LCD   back   light   will   turn   off.   Value   0   ..   100

represents 0 .. 100 % light intensity. 

Clock set value

:

 

Clock to be displayed on LCD in HH:MM format. High byte of an unsigned integer

variable represents hours (HH) and low byte represents minutes (MM).   For example value
2592 ( [10*256]+32 = 2592) will be represented as 10:32. 

Communication:  

Used   for   communication  diagnose   between   MCU   and   CP.   Normally   this  bit   is

toggled   every   1   second   from   MCU   side     and   than   Communication   feed   back   status   is
supervised on the MCU side.

4

Содержание LPC-2.DT1B

















Отзывы: