Configuration
3.13
The
Simatic PDM
(Process Device Manager) configuration software from Siemens, for example,
can configure many parameters of the Input Transducer block.
Figure 3.1 - Function and Transducer Blocks
To make the configuration of Transducer Block, we need to select the menu "Device"
Use this menu:
- To change the device address;
- To make the up/download of parameters;
- To configure the Transducer Block, Analog Output Block and Display Block;
- To calibrate the positioner; made the Auto Setup
NOTE
Auto Setup procedure for FY303 positioner in ACP.
When the positioner
FY303
is working with a pneumatic cylindrical actuator or a valve with high air inertia (slow
movement) and during the self calibration process (SETUP) is gotten 40% permanently on the LCD, please
decrease the ACP_F value using the local adjustment. For this proposal, you need to configure the ACP_F
parameter on the LCD display, using the local adjustment. Enter into the local adjustment and select one of
LCDs (for example LCD_2), then select TRD block and adjust the PRMT parameter to 114 (relative index of
this parameter in the Transducer Block). Browse up to UPD parameter to update the local adjustment LCD
configuration. Reenter into the local adjustment and then browse up to ACP_F parameter where you can
decrease the value. For an initial step, you can decrease it to 60 and then browse up to SETUP parameter and
execute the self-calibration process setting this parameter to 2 (Initialize the self-calibration process).
To make the reset by software, to protect the device against writing and to simulate the value from
transducer block to analog output block;
Save and restore data calibration.
To make the configuration of Transducer Block, we need to select the menu: Device - Offline
Configuration - Transducer.
The device
was created
as
FY303
.
Here, you can
see all blocks
instantiated.
As you can see
the Transducer
and Display are
treated as
special type of
Function
Blocks, called
Transducer
Blocks.
Содержание fy303
