SMA Sunny Boy 2000 Скачать руководство пользователя страница 26

Страница: 26 / 79

Sunny Boy 2000

Technical Description

SB2000-11:EE

- 26 -

SMA Regelsysteme GmbH

3.3.2 Connection of the PV-panels

The PV-panel’s DC voltage is connected to the inverter with safe to touch snap con-

nectors in order to provide maximum protection. The inverter is equipped with con-

nectors especially designed for PV-plants from Multi-Contact

®2

Make sure the „+“ and „-“ poles of the PV-panel are correctly con-

nected to the respective MultiContact plug connectors at the bottom

of the Sunny Boy.

Depending on the type of PV-panels you must distinguish between connecting one

single or two parallel strings. In order to be able to connect two strings there are two

connectors for plus and minus pole each. The connectors are switched parallel in-

side the inverter.

Seal the unused connectors if you are using only one string.

In order to provide maximum safety during initial installation it is

necessary to have the plus and minus pole from the PV-panels

clearly separated from the PE (protective earth).

is a registered trademark of Multi-Contact.

Содержание Sunny Boy 2000
















































































Результаты поиска

Содержание Sunny Boy 2000

Отзывы:

Похожие инструкции для Sunny Boy 2000

Бренды по названию

Популярные бренды

SMA Sunny Boy 2000, Техническое описание

Результаты поиска

Содержание Sunny Boy 2000

Отзывы:

Похожие инструкции для Sunny Boy 2000

Бренды по названию

Популярные бренды