background image

1 - INSTALL FAUCET

2 - SLIDE GASKET OVER FLEX HOSE(S) AND SECURE

3 - INSTALL STRAINER AND FLEX HOSE ONTO SUPPLY STOP. OPEN SUPPLY STOPS

A

Remove Nut, Faucet 

Retainer and Gasket.

DO NOT

 remove the O-ring 

from base of Faucet.

DO NOT 

remove 

Sensor label unitl Step 

4.

FAUCET

CENTER HOLE IN 

DECK OR LAVATORY

GASKET

FAUCET RETAINER

NUT

O-RING — 

DO NOT REMOVE

O-RING

Install Faucet with O-ring into 

the center hole in deck or 

lavatory — 

1-3/16” (30 mm) 

min. hole required.

Note:

 If installing the Faucet 

on a three (3) hole sink, a 

Trim Plate should be installed 

at this time.

B

13 mm

NUT

FAUCET

FLEX HOSE

O-RING

A

Install Strainer and Flex Hose 

onto Supply Stop.

B

Tighten the Flex Hose 

(with Strainer in place) 

securely to the Supply.

IMPORTANT: Flush dirt, debris, and sediment from supply 

line(s) before Connecting Flex Hoses.

SUPPLY 

LINE/ STOP

STRAINER

FLEX HOSE

ADAPTER

SENSOR LABEL

C

Open Supply Stop(s).

B

Remove Label from 

Sensor Window.

2

A

For EAF-200 Models, 

Plug Adapter into 

receptacle. 

Electrical Connection for up to Six (6) Faucets Using One (1) Adapter

DAISY CHAIN 

ELECTRICAL 

CABLE

DAISY CHAIN 

ELECTRICAL 

CABLE

DAISY CHAIN 

ELECTRICAL 

CABLE

TO 

ADDITIONAL 

FAUCETS  

(6 MAX.)

6 VDC PLUG-

IN ADAPTER

GASKET

FAUCET 

RETAINER

MODELS POWERED BY 

PLUG-IN ADAPTER ONLY

DO NOT pull or crimp AC 

Power Line.

NOTE:

  EAF-225 can only connect one (1) faucet per one (1) adapter.

4 - EAF-200 MODELS: PLUG ADAPTER INTO RECEPTACLE. 

     ALL MODELS - REMOVE LABEL FROM SENSOR.

Содержание Solis EAF-275 Series









Отзывы: