SleepMD Anti-Snore Mouthpiece Скачать руководство пользователя

Страница: 6 / 12

Place the lower splint under cold tap water to harden and tighten it; The

lower

usually needs

tighten-

ing.

(fig.11)

#11

Place the cams on with the hex wrench and position them all the way back. (fig. 12)

Insert the upper and lower mouthpiece back in the mouth. Check to see that the cams contact the

wings. Adjust as needed. (fig. 13) NOTE: the lower jaw remains forward.

#13

Care and Cleaning:

Use warm soapy water and soft tooth brush to clean your device after each use. Check that cam

screw is tight before each use.

In the Morning Instructions:

After removing the device, you may find that your jaw remains

slightly protruded. If this occurs, it will usually will resolve in a few minutes. If it remains for more

than 5 minutes, then lightly bite on a tongue depressor placed between the back molars. This

should be done for 5 minutes each day after use. This may occur if you clench your teeth during

the night.

#12

#13

Содержание Anti-Snore Mouthpiece













Результаты поиска

Содержание Anti-Snore Mouthpiece

Отзывы:

Похожие инструкции для Anti-Snore Mouthpiece

Бренды по названию

Популярные бренды

SleepMD Anti-Snore Mouthpiece, Инструкция по эксплуатации

Результаты поиска

Содержание Anti-Snore Mouthpiece

Отзывы:

Похожие инструкции для Anti-Snore Mouthpiece

Бренды по названию

Популярные бренды