background image

3

for various configurations of the mattress support platform shall be ± 3°,
which translates to a tolerance of up to 1 ½”.

The angle (designated “

β

” in figure 1) between the flat section and foot

section for various configurations of the mattress support platform shall
be ± 3°, which translates to a tolerance of up to ¾”.
Any adjustable foundation deemed to be within these allocated
tolerances is considered to have met the manufacturer’s quality control
standards.

THAT “NEW PRODUCT” SMELL:

Some people notice a slight odor to their new adjustable base—this
can come from our material manufacturing process. This smell is normal
and usually disappears before the product reaches you. Sometimes,
however, this smell may still be noticeable. It usually disappears after
a few weeks, providing adequate ventilation of the product and the
environment.

BREAK IN PERIOD:

You can speed up the break-in period by simply spending time in the
adjustable bed through activities such as reading, watching TV or
playing with the kids or grandkids. The extra movement will help the
adjustable base respond to weight and temperature changes. Some
of the materials in our adjustable bases such as the woods, metals
and plastics used in the platform, frame and components are sensitive
to moisture content and temperature and may make sounds in colder
environments.

PAIRED OPERATION:

When operating a “paired” split base setup there may be a time latency
up to 1.5 seconds between each bases articulation.

WEAR AND TEAR:

Wear and tear is damage that naturally and inevitably occurs as a result
of normal use or aging.

FABRIC CARE:

To prolong the life of your fabric, protect from direct sunlight whenever
possible. For spot cleaning, wipe area with a light damp sponge or
vacuum with a soft brush attachment to remove particles. Keep at a
minimum of 30cm (12 inches) away from direct heat sources. For a
deeper cleaning, blot liquid spills with a clean dry cloth. Wipe with a
clean cloth dampened with warm water. Do not wet excessively. A soft
bristle brush may be used to remove ingrained soil. Avoid scratching by
gentle brushing. Wipe with a clean cloth dampened with warm water to
remove residues. Dry in shade away from direct heat. If persistent marks
remain visible after cleaning, seek professional advice.

PRODUCT RATINGS:

The lift motors are not designed to operate continuously for more than
[2] minutes in an [18] minute time period or approximately 10% duty
cycle. Attempting to circumvent or exceed this rating will shorten the
life expectancy of the product and may void the warranty. The massage
motors are not designed to operate continuously for more than 30
minutes at a time. Please allow the massaging system to rest for 30
minutes after automatic massage shut off before restarting.

WEIGHT LIMITS:

Safety Precautions and Usage Statements

This product is not rated to support weights in excess of 750 pounds 
/340 kg inclusive of the mattress and bedding. The base will structurally 
support this weight, provided it is evenly distributed across the bed base. 
The adjustable base is not designed to support or lift this amount in the 
head or foot sections alone. Exceeding this weight restriction could 
damage the bed and/or cause injury and will void the warranty.

Содержание 633













































Отзывы: