6
25
Water inlet connection
1.The pressure of supply water should be between
30kpa and 1000kpa.
2.Don't abrade the screw thread when connect the
inlet pipes with valves.
3.Please install dropping equipment if the pressure
of supply water surpasses 1000kpa.
Two seals are supplied in the connectors of both ends
of the pipe to prevent water leaking.
Turn on the tap and check if the connectors leak.
Check the pipes regularly. Please change them if necessary.
Make sure the pipes don't be damaged or twine with each other.
The connection of inlet pipes and taps
Hold the connecting seat in one hand and
press the retaining ring and pull it down by
the other hand. Separate the seat and pipe.
Loosen the four fixed screws in the top
connector and rotate the bottom connector
to make enough space between the top and
bottom connector so that the screws can be
installed.
If the diameter if the faucet is too big, the plastic cup can be
removed.
Adjust the four screws evenly to make the
two screws near the wall fully contact with
the tap.
Make the top connecting seat block the tap
and make the seal fully contact with the tap
(please don't take out the seal).
The screw close to the wall can insert some part.
Please use the standard faucet. The mouth of faucet
must be flat. If not flat,please smooth it.
As shown in picture
,
two screws to make
it in the opposite rotating wall after
contact with the faucet with a screwdriver.
Unscrew the connector till it is tightened
(
if not tightened
,
leakage will happen
).
After unscrewing
,
the gap between up and
down connector is below 3mm
.
Washers should be connected with water inlet. Please use
attached new plumbing rather than the old.
In order to ensure the quality, water injection tests are carried out
before the washer leaves factory, so there may be water inside the
internal tub, door seals and door panel, which are normal.
Plastic cup
up connector
Down connector
Faucet
Use the standard faucet
standard faucet
longer faucet
square faucet
water pipe connector
rubber gasket
Retaining
ring
Retaining
ring
Inlet
connector
6.
Drum clean:
The program of drum clean is use the high water level, high
water temperature, high speed to clean the drum and kill the bacteria. The
detailed operations ways, please take reference of Page 18.
7.
Child Lock function:
You can lock and unlock the child lock function by
pushing 3 seconds when the machine is running.
Once the child lock function set, all the other buttons will be locked except
the power button.
After setting child lock function, the lamp will light up, meanwhile the screen
will display “CL” intermittently.
When the washing process ending or push “power off” button or default
warning, the child lock function cannot be unlocked. It means that the child
lock function must be unlocked by hand. When the power on and start the
machine, if the child lock function is going on(the lamp of child lock light up
and the screen display CL),you need to push “prewash” button for 3 second
to unlock the child lock function and then continue to operate the washing
machine.
Already set the child lock function and then want to change the programs.
Firstly remove the child lock function and push the "Start/Pause" button to
stop running, then select the required function, then push the "Start/Pause"
button to restart running.
8.
Add garment function:
During the process running, if you want to add
garment, please push "Start/Pause"button to stop running;
After around 5 seconds, it has a sound of unlocking, meanwhile the door
lock mark in the screen disappear then you can open the door.
Add the additional garment into the drum(Don't let the door clamp clothes,
this will cause failure of leakage and error).
Forced to open the door part, damage may occur, such as safety problem.
When there are many bubble in the inner barrel and plenty of water, open
the door, water and foam will flow out .
When the inner drum is running, it is in danger status since the temperature
of water is above 45
℃
and there is plenty of water inside. At this time, the
door can not be forced to open. If want to open the door, please follow the
below instructions:
(1) Wait till the inner drum stop running.
(2) Wait till the water temperature cool down to below 45
℃.
If want to
open the door when the water temperature is above 45
℃
,please shut off
the power and open the door after 5 minutes.
(3) When there is plenty of water inside of inner drum, please restart the power
and select "spin speed" button to drain out the water then open the door.
Abnormal power off for 2 minutes, you can open the door. During the process
of running, the required condition for opening door(water level below door
gasket, water temperature below 45
℃
,spin speed is 0),push "Start/Pause"
button, wait till door lock mark disappear, then open the door. When closing
the door, press the middle place of the door handle.
