background image

___________________________________________________________________________________________________________ 

REV 7/10/15 

Page 1 of 5

Skytech TM/R 2-A 

Model: TM/R-2-A

 

INSTALLATION AND OPERATING INSTRUCTIONS 

 
 

INTRODUCTION

 

This SKYTECH remote Wireless Wall Timer system was developed to provide safe, reliable, and user-friendly remote control system 
for gas heating appliances.  The system can be operated manually from the transmitter. The system operates on one of 65,536 security 
codes that are programmed into the transmitter at the factory.  

WALL TIMER 

The wall timer operates on a (2) 3V button cell batteries (included) made 
specifically for remote controls and electronic lighters.  Before using the wall 
transmitter, install the two (2) 3V button cell batteries. Follow instructions below. 

The wall timer has a 30 min, 60 min, 120 min, and OFF buttons. When any of the 
buttons on the wall timer is pressed, a signal light on the wall timer illuminates 
briefly to verify that a signal has been sent. If the signal light does not illuminate, 
check the batteries. Upon initial use, there may be a delay of five seconds before 
the remote receiver will respond to the wall timer.  

TO INSTALL BATTERIES 

1.

Remove face from backing plate by insetting a small screwdriver into the small slot
at the top or bottom of the faceplate as shown below then snap OFF.

2.

Locate the (2) holders for the 3V button cell batteries.

3.. 

Place the button cell batteries into the battery holders and snap into place. 
(Make sure that the batteries are installed with the (+) plus side as shown to 
the right. 

4.

After the batteries are installed replace the faceplate on the base.

TO REMOVE THE BATTERIES 

1.

Remove face from backing plate by insetting a small screwdriver into the small slot
on the side at the top or bottom of the faceplate as shown to the right then snap OFF.

2.

Locate the (2) holders for the 3V button cell batteries.

3.

Insert a small screwdriver into the slot at the button cell battery and pop the
battery out (Slots shown in picture above).

4.

After the batteries are installed replace the faceplate.

IF YOU CANNOT READ OR UNDERSTAND THESE INSTALLATION INSTRUCTIONS DO NOT 

ATTEMPT TO INSTALL OR OPERATE

Indicator
  Light

30 MIN

60 MIN

120 MIN

OFF

  +

Plus
Side

  +
Plus
Side

Insert batteries

into holder and
snap into holder

Insert small screwdriver

into slot and pop out
batteries from holder

30 MIN

60 MIN

120 MIN

OFF

  Insert small screwdr
into slot at the top o
      and pop cover of

30

60

120

OFF

www.FireplaceRemoteControls.com

1.888.977.6849

Содержание TM/R-2






Отзывы: