SYNCHRONIZATION
5)
Stop: if you'd like to terminate charging during the charging process, press . Under Master-
Slave mode, any operation must be carried out on the Master channel.
Finish: In charging mode, when the charging process comes to an end, the screen will be displayed
as below.
4)
STOP
[ E N D : F I N I S H ]
2 5 . 2 0 V 3 5 0 0 m A h
Parameters settings
3)
L i P o B A L A N C E C H G
2 . 0 A O F F - L I N E
L i P o B A L A N C E C H G
2 . 0 A O F F - L I N E
Press , the working mode will be blinking
L i P o B A L A N C E C H G
2 . 0 A O F F - L I N E
L i P o B A L A N C E C H G
1 0 . 0 A O F F - L I N E
L i P o B A L A N C E C H G
1 0 . 0 A
M A S T E R
L i P o B A L A N C E C H G
1 0 . 0 A
S L A V E
L i P o B A L A N C E C H G
1 0 . 0 A
M A S T E R
Press and hold for 2 seconds to start charging.
L P 6 S 1 0 . 0 A 2 3 . 1 8 V
B A L 0 3 5 : 1 0 0 3 5 1 0
CHARGE
L i P o C H A R G E
2 . 0 A O F F - L I N E
B a l a n c e P o r t
E n a b l e
B a l a n c e P o r t
D i s a b l e
STOP
STORAGE
L i P o B A L A N C E C H G
2 . 0 A O F F - L I N E
L i P o S T O R A G E
2 . 0 A O F F - L I N E
L i P o B A L A N C E C H G
2 . 0 A O F F - L I N E
L i H V B A L A N C E C H G
2 . 0 A O F F - L I N E
-
3
-
-
4
-
SWITCH BETWEEN LIPO AND LIHV
This function must be used with caution, as charging incorrect type of battery will damage
the battery, or even cause fire or explosion.
Press and hold and at the same time for 5 seconds until the corresponding battery type
appears on the screen.
It targets Lithium battery with no balance lead. Always keep in mind that the battery must be
a
six-cell battery
Turn off the
Balance Port
in the SYSTEM SETUP. Press , ON will blink;
Press or to switch to OFF; Press again to confirm OFF.
Press several times to access Charge mode.
If a Lithium battery is not commonly used, it's highly recommended to charge or discharge the battery to
3.9V with Storage mode so as to extend the battery life. If the battery voltage is higher than 3.9V, then
discharging the battery will be necessary; If less than 3.9V per cell, do the reverse. Please note both
charge or discharge must be under Storage mode.
Press the charging mode will blink.
Press or to select STORAGE mode.
PC1080 charger can be synchronized via data cables. Below illustrates how to charge 8 batteries of the
same type.
If a certain channel is selected as “Master” channel, then the other channels will be “Slave.” The settings
on “Master” can be applied to all the chargers, which saves your time significantly.
Press or to select BALANCE CHG, STORAGE or CHARGE
Press again, the current option will start blinking; Press or to
set the charging current with the range of 1.0A
－
20.0A.
Press again to choose synchronous mode. Press or to set
“MASTER” or “SLAVE”.
6S LiPo Battery
Balance Charge Mode
Battery Voltage
Charging Capacity
Charging Current
Either of the channels is MASTER, the other
will automatically change to 'SLAVE'. All the
settings must be done through “MASTER”.
Charging Time
